Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
I'd like to be able to use nrf sniffer tools (wireshark and nrf52dk) to listen to ble traffic after connection of two devices.
Is this possible?
Has anyone else done this...
I've read many similar issues that were raised regarding high SPI power consumption, looked at various examples, but can't seem to find any issue that is close to what i'm...
Hello.
When going to sleep with the BLE connection established, the WDT counter will be added. (WDT behaviour: NRF_WDT_BEHAVIOUR_PAUSE_SLEEP_HALT) At this time, my app cannot...
In the usbd_ble_uart example (SDK 17.0.2), I'd like to use the buttons handler module (the same one from the BLE Blinky example), instead of the BSP BLE button events. In...
Hi!
In our development we are using nrf52833 and for the first development phase we used the SDK 17.0.0. In that case I used the usbd_ble_uart example with s113 and it works...
Hi,
I am Using nrf52832DK and SHT25 breakout board. I can't able to read a device address using "TWI Scanner". But, I can able to scan the sht25 device address by Arduino...
Hello,
I am trying to clear reset reason when it wake-up by GPIO.
In line 163, I set RESETREAS to 0
In line 164, RESETREAS is read again.
I expect 0. But It still...
Hello,
I use nRF52832's COMP (comparator) to sample a pulse signal's voltage level.
I found when the pusle width is below like about 60us, the COMP can't get correct...
Hello,
we need to feed mono audio data into the nRF52 and we are now evaluating the possibility to use PDM. The nRF52 seems to have a useful PDM interface , and even though...
Hi,
I would like our nrf52840 to use coded phy 8x to get longer range.
The counter part are Android smartphones, old ones with BLE 4 support only, new ones having coded...
Hello,
I have a custom PCB which uses the NRF52832 chip and i wanted to program it using the NRF 52 DK using P19. I have the following connector and pin out on my custom...
Hello everybody !
I am working on a project and I need to create a server node which also works with the nRF SDK.
As I have seen, it exits coexistance examples where both...
Hi there,
I am trying to use the ISP from the 6700. I need to power my development board. I was wondering if there is a pin output on the nRF6700 motherboard? There is...
