Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I have try to midify：
// <s> NRF_DFU_BLE_ADV_NAME - Default advertising name. #ifndef NRF_DFU_BLE_ADV_NAME #define NRF_DFU_BLE_ADV_NAME "User Name" #endif
but it does...
For flash memory, 10000 write/erase life is specified in the documents. is that means 10000 lifetimes for writing only and 10000 only for erasing? I have to delete the page...
Hi,
I'm trying to flash my network kernel code to the nRF5340-PDK network core over JTAG. It's a custom research OS called Tock that you can look at here . The code is fairly...
Hi everyone!
I want to send data (with nRF52832 chip) on a mobile phone every 1 ms, is it possible knowing that the minimum connection interval between a peripheral and...
Hi,
I am have programmed my Thingy 91 device with lte_ble_gateway program to collect data from 5 bluetooth devices and send them to the cloud. This program runs fine,...
Hi all,
I've a custom board in which I'm trying to interface SD card with nRF52840 chip.
I've checked connections with multimeter for connectivity and added pins accordingly...
I'm new to the NCS/Zephyr environment. In the past I got the nRF52832 working with the VL53L0x. I ported arduino code of the VL53L0x and got it working well. But now I'm trying...
I have never seen documentation this opaque. How on earth am I supposed to use this documentation to write C code? I can't find any macros, static variables, nothing to get...
Application blinky example hangs when connecting with android app. I get 0x4001 error in app_error_fault_handler().
It is strange that when i use blinky app on android it...
It was my first time working with the Segger embedded IDE
SEGGER Embedded Studio for ARM Release 5.42 Build 2021031901.45616
and NRF52840-DK.
PCA10056
2.0.0
2020...
I have a problem with printk/LOG in one program (samples/sensor/bmi160). All my programs, except this one, gives me serial output from both logging (LOG_INF etc) and printf...
I bought the PCA10056 board. I want to develop my own application over the ble_app_template example. How do I create a ble service? how do i create uuid? I'm confused. could...
Hello,
I tried to setup the UART example provided at this link: https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160
I open two COM ports...
