Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hi,
I'm currently trying to build a quick frequency spectrum scanning tool on an nRF52840 dongle. I want to sample RSSI on a list of channels as quickly as possible in a...
hello,
we're working with the nRF52833 and are experiencing some issue with the I2C interface during communication involving clock stretching. We're wondering if the errata...
Hello guys,
I am dealing with a problem, i have two tasks with two different spi instances, alone they work fine, but when i want to run both tasks they crash!!
Hi!
I met some issue ).
I use nrf mesh app on my phone and change it for my goals. I would like to get messages from nodes to phone via mesh. I read some posts that it...
Hi,
While developing an app which will connection to an IOS device via BLE - I've noticed an event called BLE_GAP_EVT_PHY_UPDATE_REQUEST.
I understand that this event...
Hi,
I'm using NRF52840 in order to connect to a mobile device, with PIN code.
Connection to Android is ok. The issue is with IOS.
IOS can't send the PIN code to my...
Hello, We're trying to optimize the data transfer rate from our nRF52832 based peripheral device to the mobile phone. Tested with two different BLE >= 5 Android phones we...
Hello, I ve made a custom nrf52832, but ive face a lot of problemes : when logs is on the BLE is off(its not advertising) , I m not able to see it on my app. when my module...
Hello,
I am using MacBook and would like to import Keil Projects into Segger Embedded Studio by following this guide , but finally I got an error is that
I have found...
I have some questions about nRF9160.
1. What is improved comparing to revision1? Only power consumption?
2. Is GPS sensitivity improved? In revision1, it is poor.
3...
Hello!
I use light switch example in a 52DK with a 4.1.0 mesh SDK. I modified the original project and implemented the custom element model for sending arrays via mesh....
Hello.
I'm testing the integration of the BLE and TWI.
However, BLE advertising function when turn on, TWI data was not correct read.
Can you tell which one is...
Hi, I am saving data in flash memory but when I read after restarting the device it shows FF. How can I read from flash after restarting the device? and how can I check that...
Hi, i am very new to nrf family. when i use sprintf function with %d specifier, it works fine. but if i set it to %2.1f or anything with "f" included doesnt work and program...
In the ble_app_hrs_rscs_relay application, three ( NRF_SDH_BLE_TOTAL_LINK_COUNT=3) queued write modules are generated.
(one for a peripheral (server) role and two for two...
