after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi! Some prerequisite info:
We are using nrf52840 boards as our peripherals
We are using v16.0.0 SDK
We are using the s113 SoftDevice, more specifically s113_nrf52_7...
Hi,
I have a topology which has 20 to 50 nodes and these nodes should send a data packet of approximately 20 bytes at 50 Hz to a single gateway node. Is BLE mesh suitable...
hello nordic
i have been working with nrff52832 with the SDK16.0 (also working with s132 if it matters)
it is a real head braking to deal with your never ending sdk_config...
Hi team,
Do we have any evaluation on the nRF Connect SDK size if customer wants to run on nRF9160? Customer wants to evaluate their Flash/ RAM buffer for APP.
Thanks...
Dear Sirs,
I am trying to use the FDS Storage Library to store 4word = 16 bytes in to flash.. Which seems to be working fine. No errors and the function is shown below...
Hi,
We have custom board based on nRF52833 SoC. We are trying to use SDK_v16.0.0/examples/ble_peripheral/ble_app_uart/pca10100/s140.
Using Segger Embedded studio, program...
I'm planning not to have a device name UUID in the advertisement packet, instead set scan filter based on manufacturer-specific data. Is this possible in SDK16? If so please...
Hi, is there any public repository in which I could track changes in zb_cli_wrapper library? I had problems migrating from 0.2 to 0.3, and don't want to do this another time...
Hi!
Since I do not have a SIM card that provides support PSM or eRDX I need to switch the system mode manually.
In my config I have CONFIG_LTE_NETWORK_MODE_LTE_M=y ...
I generated boot-loader (logging disabled) from SDK 12.1.0 for adding a signature check during DFU for nRF51
The problem I am facing is with the size of bootloader (hex...
Hi I checked the relevant topics in the forum but none of them fixed my issue so I just create a new one here.
Basic info:
Hardware: nRF52 DK PCA10040
SDK: nRF5_SDK_15...
Hi,
I'm having issue connecting to the nRF52840_DK through J-Link and nrfjprog. I was able to connect to it the first time and upload simple BLE sample, but afterwards I...
Hello,
I'm developing an app for nRF Connect Desktop based on the nRF Connect Desktop BLE App.
I would like to find a characteristic item based on an UUID. Where is the...
How is it with SUPL and NB-IoT, will it work? AFAICS, in the example code, the supl_support code only uses TCP, and this is not a protocol supported when the device is using...
