Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hi, i have two boards with me i.e. nrf52840DK and nrf9160DK. I want to debug nrf52840DK using nrf9160DK, I don't want to use onboard jlink on nrf52840Dk, is it possible to...
Hi! I'm currently using
- board: nRF52840 DK
- SoftDevice v15
- ble_app_template example + midi (adding custom service and characteristic) -------------------------...
Hi,
I used SDK 16. softdevice: S140 v7.01. And set APP_USBD_VID and APP_USBD_PID to 0 at sdk_config.h
I follow this post of https://devzone.nordicsemi.com/f/nordic-q-a...
I'm trying to have nRF9160 DK communicate with an external accelerometer.
nRF9160 stop working at the function of i2c_reg_read_byte in the code below.
Does anybody give...
Dear fellow developers
I would like to integrate a smart lock ( danalock v3 ) with the alarm system, so that I can control the lock via the alarm system. The alarm provides...
Hello,
I have a few questions regarding power consumption of the BLE modules
With regards to the nRF52810:
The data sheet lists the following as specifications for...
Is there a quick way to disable MCU Boot on the Thingy91 Asset Tracker example? I need to use the button on the device to my applicaton, and it is neccecary that the user...
Dear Sirs, good afternoon
I am using a (PPK + nrf52840 DK) to measure current on an external device.
Is it necessary to cut the SB40/41 jumpers in this case?
Thanks...
Dear Nordic ：
I want FTMP (Fitness Machine Profile) to be supported in my product (A smart trainer uses NRF52832, called Gravat in Ant+ official website).
I find that...
I want to monitor the RTC count and generate an interrupt when a specific count is reached. And without stopping the RTC, I want to generate an interrupt again when the next...
Hi
We have the issue that GPS has no fix.(board: Thingy91 version: 1.0.2) I used the pre-compiled hex thingy91_ltem_dfu_2020-04-29_bc7ade8b.hex downloaded from Nordicsemi...
i want to connect Nordic thingy to a nrf 52840 soc with ble central example.
all i want to get is thingy environment service and get temperature and humidity values on...
Hello,
I got the acceleration value using mpu6050 sensor. And I am going to use this to get the angle of the sensor. The formula below has shown that angles can be obtained...
