after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I have a question on stack guard that I tried to enable on nRF52840 and hope you can give me some pointer to verify it is functioning properly.
Basically, I call nrf_stack_guard_init...
Hello i am making an application using hid over gatt. i changed original keyboard usb description with fido description for test, however, i don't get any event through. I...
the link i given below tells, how to make a haptic glove using arduino mega
https://hackaday.io/project/160405-diy-haptic-glove-for-vr
i want to do it with nrf52840 DK...
Hi everyone,
I'm working on programming nRF52833. I want to my nRF52833 is able to broadcast advertising and also scanning (In another word, my device plays peripheral role...
Hi
I have upgraded from an early version of SLM to the latest version in nRF Connect SDK ver. 1.3.1
the SLM application is running on a custom board with a nRF52840. Using...
I found this application very useful!!
The code is now at the Github.
I found there are some problems to reconnect - it gets many errors and the peripherals eventually...
Hi, I understand there's no high level TWIS (i2c slave) driver for nRF9160 (i.e. in Zephyr); as such, I need to use TWIS driver that's part of nrfx, or even lower (HAL) level...
Hi,
I need to upload compiled binaries from mbed studio to my custom board based on nrf52840 using nrf52840 dk.
I have replaced the jlink software( J-Link OB-SAM3U128...
Hi,
I have a product that needs to send 256 bytes of data to an IOS or Android phone upon request from phone. We are currently using the Nordic UART app to receive the data...
Hi,
I have an issue with OTA DFU stop working after updating softdevice_bootloader through OTA DFU, and the problem seems to be in the MBR params page.
The scenario is...
Hi everyone,
When I am scanning the advertising packets of nRF52840 peripheral, I see that Device's address is type of Random Static.
1. The Static Random Address is a...
HI, I know about the proxy feature/nodes and the way in which a smartphone can connect to a proxy node and send a message. However, in the mentioned method we need to connect...
I find that the low current readings in the Average and Trigger windows can vary significantly. I understand that the sample rates are much different, but does that also affect...
Hi,
I am trying to set the section placement macros on the segger embedded studio. Follow some instruction, find "project -> Option -> Linker" I cannot find the set about...
