after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I'm attempting to control the microphone level from Windows 10 and Mac OS by configuring a Feature Unit.
The USB audio example demonstrates how to configure a feature unit...
Hi,
I am using the uart example from https://github.com/Rallare/fw-nrfconnect-nrf/blob/nrf9160_samples/samples/nrf9160/uart/src/main.c
I want to read serial data from...
I'm making my own protocol on nRF52832 devices and I'm wondering if there's any possibility to have data corruption when CRCSTATUS contains CRCOK value.
I'd like to get...
hi all,
I am using the following example:
"..\nRF5_SDK_12.3.0_d7731ad\examples\ble_peripheral\ble_app_uart_adc_scan_mode" to send via bluetooth data coming from ADC. ...
Hello, team.
Thank you for helping.
I was wondering that what is the difference between 'managed flooding' and 'relaying' in mesh.
The only one that I know is provisioning...
Hi,
I am just a beginner in this field and need support to proceed.
I want to have a BLE Mesh network using lights, switch and occupancy sensor. In this I want to use...
Hi,
I need to modify the ble_central_hr_c example to connect to the hear rate strap with the best rssi.
For this I got to say listen for 10 seconds or so to all the...
HI,
I want to update the application FW in mesh sdk environment from flash memory. The new binary is in the flash memory already (I received it from a spi-ethernet interface...
Hello,
I am working on the nrf52832 board. I am using the NUS example as the base.
For my application i need to send encrypted data from the phone i.e central to the board...
Hi
Tring to setup development environment using nRF Connect for Desktop ( nrfconnectsetup342ia32.exe), in Windows 7 host.
Used tool manager to complete all necessary necessary...
Hi,
we are using both system on and system off power mode in one of our application.
Sytem on : wakeup through RTC for an every 60 seconds once / GPIO.
System Off :...
Using nrf_mesh_sdk_4.0 and ble_sdk_16.0:
1.I want to load light_switch_server code on nrf_dongle.
2.And then take data from r-pi through usb of dongle and publish it over...
We have been using the nrf9160 successfully for several month. I'm currently upgrading our products to use the new modem firmware (1.2.0) and, together with that, to the most...
