Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Somehow my nRF9160 DK board has become essentially unresponsive. Flashing new modem using nRF Connect Programmer, and downloaded nRF FW, "seem" to work. But nothing else....
The asset_tracker repo now has a file called: prj_nrf9160_pca20035ns.conf
Is this still compatible with the nRF9160 DK that is using pca10090n ?
What does the pcsNNNNNn...
Hello everyone,
im using the nRF52840 DK, softdevice s140 and the ble_app_tamplate example. In this example i can send data through the GATT protocol. But i want to change...
Hi ,
I would like to know if the .dat file inside the DFU packet is always the same or it can be different.
Is it Possible to fix inside the code ?
What is the .dat...
Hi all
We are using nRF9160 DK & want to test its MQTT library by uploading some data to the broker. But, my city doesn't have LTE Cat-M1 / NB-IoT network.
Can you suggest...
Hi,
1. ZigBee Cluster Library Specification(Rev 6) -> 3.3.2.2.3 Battery Information Attribute Set -> Table 3-18. Attributes of the Battery Information Attribute Set tell...
Hi,
I am a beginner to nrf9160.
I already can do send the large data to server. (Maybe not too large just about 15KB)
In my test, I will send that data in every 25 minutes...
Hi,
I am not able generate dfu_package.zip using nrfutil.
I am using ubuntu 18.04, and python2.7 is installed is default python version.
I get the following error when...
Hi!
I have bought the Thingy:91 and in user guide (on page 12) it says that the nRF91 DK should be used to update the modem firmware, further more, it seems like it is only...
Hi I am trying to program the bsp buttons on the NRF52 DK, so pushing button 1 will toggle start advertising and going to sleep by calling sd_app_evt_wait().
I have successfully...
Hi All
I'm trying to use the Adc in Sample convert mode: "nrfx_saadc_sample_convert(0,&ADC_Val);" to sequential read two ADC pins .
I have used the code below to init...
I want to add a node(server) in multiple group in Mesh.
Application is if any switch pressed next two corresponding light to be trigger to on. for that one server subscribe...
