Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Dear Nordic,
I want to achieve long range in my custom board
I have some doubts:-
1. is it any difference in schematic for achieving?
2. Which HF crystal i used...
Hello, I was wondering how can I send data continuously over NUS.
I am using the ble app_uart and app_uart_c to program two NRF52382 with s132. My goal is to sample a signal...
Hi
SDK 15.2.0 ch_map[5] is 5 bytes long so 40 bits. Can you please confirm if ....
ch_map[0] bit 0 corresponds to channel 0
ch_map[0] bit 7 corresponds to channel 7...
the Product Specification v1.4 of the nRF52832 SoC. On page 23 the RAM0 block section 1 address is given as 0x21001000. From the context I believe, this should instead read...
Development Kit - nrf52 DK
SDK - 15.0.0
Computer Platform - Windows 7 - 64 Bit
My application was working fine until I decided to change the NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
Hello everyone!
I have a question regarding where should I place NRF_DFU_SINGLE_BANK_APP_UPDATES flag. Should it be inside sdk_config.h in a bootloader or application? Or...
How to enable and disable FreeRTOS tickless idle(RTC or Systick)? Anyway to wakeup from tickless idle mode when there is BLE activities detected?
Setup:
1. nRF5_SDK_15...
Compiled Blinky client fails on Dongle PCA10059.
Precompiled version nRF5_SDK_15.2.0_9412b96/examples/ble_peripheral/ble_app_blinky/hex/ble_app_blinky_pca10059_s140.hex...
I am trying to compare a bunch of BLE mesh options and I am trying to evaluate the software stack for nRF mesh
Whilst trying out the light switch proxy example, I noticed...
Hi Great Nordic Team:
I have some questions about nrf24ap2 reference schematic, please kindly help to give me some tips.
※it's reference circuit of Synchronous (bit...
Hi Sir,
As reference below link, and we can find the Tickless IDLE enabled ~700uA in SDK 15.2
https://devzone.nordicsemi.com/f/nordic-q-a/24733/nrf52840-sdk-14-0-0-and...
Hi again!
I'm trying to send/receive data between an nRF51(master) and a AVR/HM-11(serial/BLE module)(peripheral)
After following this visualgdb.com/.../ tutorial based...
Under some conditions I want to force advertising to transition from slow to fast. With SDK 14, I could just call ble_advertising_start(&m_advertising, BLE_ADV_MODE_FAST)...
Earlier for nrf52 we could filter out connections on the peripheral based on rssi, need similar operation for nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\ble_app_uart...
Dear Nordic,
I have one nrf52840 dongle.I want to know which polarization of antenna (PCB antenna) gets maximum range?
another thing i want to know what is the maximum...
