I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Hello,
I am looking for (10) pieces of the tiny nRF52810-CAAA for a prototype.
Apparently, distributors do not yet have any stock and the lead time is 14-16 weeks.
Might...
This is probably a very easy question to answer and I apologise for not fining the solution myself but I have been trolling through the documentation for several hours now...
I am doing rapid development for a project, using the nRF52840 DK. Two key features are USB and BLE central role.
I started with the usb_cdc_acm project and am merging in...
Hi all,
I added newliib-nano to my GCC project, when I use new ( std:: nothrow) I got
I add some C++ flags and link flags:
custom-nano.specs:
How should...
Hello everyone!
I have been working on getting data from ADS1299 ( ExG bio-signal sensing). I successfully got data from this IC using STM32F407VG (Cortex M4) and transmitted...
Hi I'm using custom nrf52832 board, SDK14.02 and SES. I want use pwm driver to generate 2 channel pwm wave with custom nrf52832. Everything is working fine in nrf52DK board...
Hi,
I am to update the SD version that I am using, and in the documentation to create a firmware packet with nrfutil states that the table can vbe found with nrfutil pkg...
nRF52832 / SDK V15
Hello,
Is there is way to read the nRF52 flash memory (any location if possible) over UART without uploading a program in the flash memory for that...
Hello ,
I'm trying create a beacon Scanner.
I'm using the s130 protocol stack on the nRF51 DK , namely the nRF51422 SoC and PCA10028.
what I'm trying to achieve is...
I am trying to work through the MQTT-SN Examples that comes with the Thread SDK. When I use the prebuilt image for the Raspberry PI 3 board everything works great however...
Hello,
I use an I2C device to wake up a nrf52 microcontroler.
If I just use the init function
static ret_code_t twi_master_init(void)
{
ret_code_t ret;
const nrf_drv_twi_config_t...
Hi,
I'm using Segger Embedded Studio (with gcc naturally). The standard C++ exception handling doesn't work: exceptions are not caught by exception handler. Is there a way...
I have read a lot of the Dev Zone questions here about the RF Antenna design and read the PCB design guideline tutorials and skimmed some of the white papers. Of course the...
The current example TWI_handler will hang forever is it exits with anything other than NRF_DRV_TWI_EVT_DONE. This can occur if a TWI slave fails to acknowledge the address...
Hi,
Based on the electrical specification of nRF52840's HFCLk, the current consumption seems quite different depends which crystal is being used (attached the screenshot...
