I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Hi I want to ask about the best way to handle a lot of incoming bytes via UART on the nRF52832 (SDK 15.0.0). Unfortunately, the parsing of incoming data seems to be slower...
We are moving from using the Device Manager to the Peer Manager.
We are concerned about side effects concerning updating customer device firmware. One issue of concern is...
I stumbled upon Nordics video on facebook where they show how to calculate the distance between two NRF52840 Dev Kits. Link to video and article: devzone.nordicsemi.com/....
I downloaded version 15.2.0 of the nRF SDK. It contains the softdevice version 6.1.0.
I then attempted to upgrade to the softdevice to 6.1.1. After downloading the softdevice...
Hello,
What are the steps to recover a bricked nRF9160-DK? I want to get it back to the state that it was shipped in. I would assume refresh "secure_boot" and an app such...
Sir,
I have one custom MDBT50Q evaluation board and a ST-Link debugger. As the Keil IDE is fully defaulted to J-Link none of the example programs are building and flashing...
Hardware:Two nrf52840 DK Software: SDK15.2
We have 2 development boards acting as a master and slave communicating over UART. We are using the serial library for this application...
when i use the official example in nRF5_SDK_15.2.0_9412b96\examples\peripheral\blinky\pca10040e\mbr\iar using IAR IDE,
after building successfully, i failed to download...
Hi:
I use the new Mesh SDK 2.2.0 to make a demo.and I use the proxy_server and proxy_client example. now，I test and find the proxy_server example don't open the relay function...
Hi,
When I go through the code of light switch example, I am confused about relay functionality.
Compare with the v2.1.1, I can find the m_relay_enable in network.c but...
Hello!
We are currently developing a software solution which integrates many protocols into one Gateway. One of the protocols is Zigbee, and since it is the first time we...
I'm running FreeRTOS with SDK version 15.0 on nrf52 custom board.
I have two sensors, say A and B, on two separate SPIM bus instances. Sensor B utilizes PPI to trigger data...
I've been working on using an nRF52 as a host for a PS/2 synaptics touchpad mouse (to integrate with BLE HID). I was able to get a correct mouse position using two GPIO pins...
Hi,
i am using oled ssd1306 i2c with nrf51822. I am using peripheral mode and SDK v10.0. i choose this sdk version because of length i want to sent at one go that is 1024...
Help pls, i can't build a project.
Building ‘temp1’ from solution ‘temp1’ in configuration ‘Debug’ 1> Generating linker script ‘temp1.ld’ 1> Linking temp1.elf 1> Output...
