Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
I have a suggestion for an additional feature to nRF Connect for Desktop:
When doing DFU with a zip package that contains a bootloader + softdevice -combo and an application...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
Hi,
I have a pretty extensive nRF52832, SDK14.2, freertos project built and debugged using Keil MDK.
I'm trying to port this project to SES and experience some problems...
Hi,
LED is on when the button is pressed. Press the button again and the LED off. I want the Turn the LED on as long as I press the button. Turn off the LED when I stop...
Hi there,
I've already implemented a custom firmware for nRF52832 with SDK 15.0.0 and S132 v6.0.0 which uses both advertising and scan operations, and now I'd like to use...
Hi all
nrf52840 Development board,sdk is nRF5_SDK_15.2.0_9412b96 ,PC is windows 10
I'm wondering why the pairing request sometimes shows up in the notification bar and...
Hi,
I am using nRF52832 with sdk 15, freertos.
I need to implement the following logic:
1. Get into low power mode, while keeping a timer running.
2. Every 10 mins...
I was using NRF52832 and s132 v6.0.
I have Android phone's IRK and I have added the Android phone into the identites list manually.
After doing the direct advertising...
In the NRF52-DK user guide, the following is stated:
Important: When using ANT/ANT+, the 32.768 kHz crystal (X2) is required for correct operation.
However, I could...
I need a help to create a mesh where two nrf52 dk are connectred in the mesh and one node sends a message and another node recives it and sends to a url
Hello,
BLE MESH 3.0 Light Sw Example code just I have add APP_TIMER_MODE_REPEATED and its work fine.
Case 1:if I print string Or LED Toggle Based on timer its working...
Hei there!
First of all thanks for all the great work here!
My question is:
In my application, the final device will have 4 pogo pins.
Two of them are for power, the...
Hello All,
Hello all,
I am working on BT832A in which nRF52810 is used and i used segger studio for programming in windows 7. I am refer nRF52 SDK 15.2.0. And i am load...
In the manual for the nRF5284 there is a listing for some divider settings for the MCKFREQ. The size of the register and the values to set indicates that there are a much...
