Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using the FDS functions to save needed data to flash and retrieve it when needed. The init, writing, and reading all function correctly. However I am running into trouble...
Hi,
I'm having some issues when trying to make a HID device work with Windows 10. It says 'Connected' but then changes to 'Device Error' a few seconds later. I get 'Error...
Hi,
Im tryin to use the ble_dfu service example from SDK12, I get DFU SERVICE NOT FOUND when trying to update from Android.
Any suggestions what to look for?
I use...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hello,
I am using the NRF52 to send sensor information over bluetooth using Nordic UART Service. Can the same service be used to send strings?
Thank you.
Hi,
I'm developing to nrf51822 mcu, using a s130 softdevice.
I'm using a BLE example code.
I get an interesting problem - when the mcu receives 2 reports (that are...
Hi,
we are thinking about using the NRF52 with the BLE SoftDevice in a security relevant application. As the SoftDevice is not available as source code, no reasonable security...
Hi all!
I want to check work of AES encryption.
Some code on 51822:
uint8_t aesKey[]= {0x31,0x32,0x33,0x34,0x35,0x36,0x37,0x38,0x39,0x30,0x31,0x32,0x33,0x34,0x35,0x36...
Hi All,
I have a problem with the function sd_ble_gatts_hvx().
I have no return value when i call this function and i don't understand why ?
I have a function where...
I am running SES 3.10f on Linux. I have followed the Tutorials regarding Monitor Mode Debugging. I don't ever get the pop up box regarding the Monitor Mode debugging license...
Hi All,
My question is about available sleep modes in nRF51822.
As I can find in nRF51 Series Reference Manual, and Product Specification documents, nRF51822 chip has...
Description:
I am developing iOS app which will connect BLE and keep the connection till user don't want to disconnect. i.e we want to autoconnect BLE when BLE is in range...
Using Master Control Panel (MCP) with nRF51 Dongle PCA10000 v1.0
Segger is offering a J-Link firmware update - v6.10l:
Is this compatible with MCP? Is it safe to...
I am using RedBearLab Blend v1.0. I ran the HID_template and HID_keyboard_template. I can see the device in Win10 advertised as joystick and keyboard. Then I tried to modified...
Hello , i am going to use nrf51822 development kit ,but i am totally new for using it, i want to know that if i have development board and i want to see result but i dnt have...
