Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I try to modify the RX message of bt_receive_cb, but every time RX receives a string, RESET will occu.
How can I fix this issue?
>Demo code:peripheral_uart (SDK2...
To the kind attention of Nordic support team,
I'm running ble_app_hids_mouse_pca10100_s112 in a PCA10100 dev board. It is the sdk17 program, where:
1.I added 2 files ...
Hi there,
We are currently running tests on the nrf9160 DK using an iBasis SIM card, which should be capable of connecting to multiple networks. We are trying to understand...
Hi,
How is the LTE-M or NB-IOT network availability for very much remote locations like forest or mountains for emergency use cases compared to low-earth orbit satellite...
NCS ver: 2.0.1
chip: nrf52840
node: MTD not SED
network: one OTBR as leader and one MTD as child
After about 4~10 hours, MTD will offline. Sometimes it can reconnect...
I like to enable compiling my code with c11 or c17 but when compiling with west this does not seem to be possible.
To force the compiler to use c11, I used option:
CONFIG_COMPILER_OPT...
Hello,
I am experiencing a SoftDevice Controller ASSERT: 62, 1846. I am using a nrf52832 acting as a peripheral and nRF Connect SDK v1.9.1. This assert happens when large...
BLE-app-blinky client not working
BLE-app-blinky sample build success, LED1 on, when connect LED2 on, but i can not see client service uuid in my android app.
i cannot...
Hi there,
We are doing some testing on an eSIM with the nrf9160 DK, and we are looking for an AT command that can be used to read the eUICC ID of the SIM. We are using the...
Hello,
We are planning to integrate the LwM2M carrier library. Our system uses mfw 1.3.3 and NCS 2.1.0.
Based on the following page https://infocenter.nordicsemi.com/index...
I'm trying to update MCUboot from the application. As a first test, I enabled the flash shell commands. I can erase somewhere within the flash without problems:
uart:~$...
Hi,
I have a simple SPI circuit to read data from a flash memory W25Q64 to be exact and I have difficult time reading the device address of the chip through SPI.
The situation...
Hi Devzone,
we are working on nrf5340 mcu, from the DTM sample, l learned that the application run on network core only, but my application scenario is combine the DTM with...
Hello,
I'm using the SAADC voltage conversion formula from the Nordic example as follows: 10 bits are used in the example.
By the way I want to change ADC resolution...
