Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
If I send 0x33 through the project example in the directory “nRF5_SDK_17.1.0_ddde560\examples\802_15_4\wireless_uart”.I can see the data 0b 61 88 01 34 12 0b 00 0a 00 00 33...
Hey
For nNR2805, using SDK nRF5_SDK_17.1.0, when we include the LESEC Pairing, we got the binary file with a size bigger than the flash size
Should nNR2805 work with the...
What is the behavior if back-feeding the nPM1100's VCC output, such as if VCC is supplied from a external supply and no battery or USB power is present.
I have been bringing...
Hello!
Tyring to configure the uart rx/tx pins pull-up, pull-down or open-drain using the ncs 2.0.2 . So far I couldn't do it. For example "bias-pull-down" seems to have...
Hi there, I'm having trouble programming the Nordic Thingy:53. I've got a nRF53 dev kit connected to it via the 10 pin connector (as per the instructions) and of course I...
hi，
I`m project NRF52840-SDK_17.1.0。 How do DFU use the uart?What applications do I use for Win7?I read a lot of other`s qusedions-answers,but I still don`t know how to...
I have a working project on a custom board based on nRF52832 ( PCA10040, S132). This board is a BLE Peripheral.
My task is to migrate this to a custom board based on nRF52833...
Hello, I've been using the modem library from NCS1.7.0 specifically 'at_cmd.h' and at_notif.h'. Now I'm trying to port to NCS2.0.0 and I believe that the AT CMD interface...
Hi,
I've got a display driven over SPI at 8MHz by the lib LVGL in a dedicated Zephyr thread and an ISR configured on one gpio pin that triggers a short routine registering...
Hi,
I'm testing the matter commissioning from your sample "light_bulb" on the nRF Connect SDK v2.1.0
I have this setup:
- One nrf52840dk flashed with the light_bulb...
Hi, In order to adjust the sound pitch a magnetic buzzer I thought using a PWM could be the right choice. Looking at the nrf5340dk device tree source I've found a pwmleds...
Following Setup:
1.) Building light-switch-app from original https://github.com/project-chip/connectedhomeip Repo for nRF5340 from command line with nRF SDK v2.1.0
2...
Hi,
We are close to going into a certification process but before we start we need to be sure we are not missing out on your recommendations with regards to EMC performance...
Hi,
I get the error like below on the Linux XFCE 64-bit platform (Pardus 21.2 distro latest version). It works fine on Windows but having a problem on linux. How can I solve...
Dears,
Currently, when working with the nRF52833dk, I found some weird behavior.
I tried to run the blink example in nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_blinky...
