Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Under Ubuntu 20.04 the udp sample application that we have modified that builds with no problem under nRF Connect SDK v2.0.0 fails to build when when its directory is copied...
Hi all,
I want to evaluate the nordic ranging toolbox and compare it to a proprietary solution. First of all I set up the distance measuring example ( developer.nordicsemi...
Hello,
I have an existing application based on nRF52840 but it is using native zephyr and native MCUboot.
By 'native' i meant using the upstream versions of zephyr and...
In the Zephyr documentation, the explanation for NVS sector erase is a little ambiguous.
Elements, represented as id-data pairs, are stored in flash using a FIFO-managed...
Over the past 2 weeks the programmer fails to recognize my9160DK board. Instead, I see it listed as "J-Link" in the device list with a serial number underneath. The programmer...
Hello! I am discovering a new approach to nRF52 development. I used to be quite happy with SDK+Segger Embedded Studio. But as I understand it, this is an outdated method....
I can't figure out how to run sample code that uses the LTE-M modem.
I see nrfxlib has a modem library. But I don't know how to make a simple sample app that uses this...
Trying to build and flash the nRF5340 Audio application to my nRF5340 audio DK eval boards for eval purposes. Apparently this requires access to the LC3 repo so I am seeking...
Can you share the source impedance measurement for the nRF52840-CKAA? Is the T-network only for impedance matching? Do i need a filter for harmonics if I'm planning to transmit...
I'm using the pc-ble-driver-py: Standard Heart Rate example to read a characteristic just fine.
My issue is i now need to write a to a characteristic.
How would I do that...
Hi
I've recently been working on the ncp host example provided by nordic. after downloading the standalone version from the site, I tried programming the 2 nRF 52840 dk...
nRF SDK 17.1.0 with SD140 7.2.0
There is no example for how to use the sd_rand library. I've seen scant few posts that mention functions like sd_rand_application_bytes_available_get...
Hi I've just started developing with the nrf52840 and Ive been following the official documentation on how to use the programmer shipped with nRF Connect.
Unfortunately...
Hi,
In a custom nrf52840 board (DC/DC=on, LFCLK=RC, CONFIG_SERIAL=n), using ncs2.1.0, I measure through PPKII ~6.7uA in system_off mode, which is reasonable.
In system_on...
I have a similar question as in the previous post (about 4 years ago) with title "nRF52 WLCSP DCC routing - - ok to run over GPIO pins?" by Laserdan, i.e., I would like to...
