Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
Hello,
Been chasing this undefined reference to `__device_dts_ord_XXX' issue around for awhile now with no clear path forward. What I am observing is extremely similar to...
Hello,
I am working on Thread client server based network. I am using nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8. My development hardware is nRF52840-DK, HW Version 2...
Hi,
I am using nrf toolchain v2.0.0, and am testing the dfu-ota example over BLE by following the below link ( ) . howveer for fast boot up, i am using "
CONFIG_BOOT_VALIDATE_SLOT0_ONCE...
It is possible to change the partition table through a FOTA?
Is the partition table stored somewhere on the device, or is it merely used for linkage? If it is linkage only...
Does anyone know how to use the CMSIS-DSP FFT library on a nrf52832?
I am using the nrf Connect SDK and it seems all of the examples are for nrf5 SDK.
I am looking to...
i use the ubuntu20.04 and open nrfconnect-3.11.1-x86_64.appimage through proxy successfully
then i install and open the toochain manager , there is not include NCS 2.0...
We are developing a new product and plan to use nRF52810. As I understand nRF52 will be supported for production in the new nRF Connect Release (1.3.0) that will come soon...
Hello,
Our application requires the device to go into deep sleep and wake up every 24Hr or on the Accelerometer interrupt. We were able to obtain the sleep mode and wake...
I'm trying to migrate my project to NCS 2.0.0 but having an issue like below:
c:/ncs/toolchains/v2.0.0/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm-zephyr-eabi/10.3...
Hello everyone,
I am working with the SDK v17.1.0 with the DK nRF52832 with the examples of ble_app_uart and ble_app_uart_c.
I managed to implement a multilink communication...
Hi We have designed some boards with ESPRESSIF WiFi BLE Module ESP-32-WROOM-32E for control and monitor.
Is it possible to connect esp32 to nRF21540 to extend range ( such...
Hi, I am using nRF52840 and communicating with Simcom GSM( Sim7600g ). 1- Is there any example code/ Library to connect with the MQTT server?
2- Can I use this example code...
I found my thread device to have quite a large latency so I analysed the communication and found out that the device is actually timeouting and retrying before listening for...
We are trying to connect MQTT over IPv6 with nrf9160dk and custom board. We are using mqtt_simple sample.
Software NCS version: NCS main (latest)
Changes in the code:...
