Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
I'm stuck with trying to install Nordic/ANT+ SoftDevice SS340-SD-v6.1.1 on the Adafruit Itsy Bitsy NRF52840. Within nRF Connect - Programmer, I am getting the following error...
Is it possible to use a NRF9160-SICA-B1 for a pcb designed around the NRF9160-SIAA-B1? Based on my findings, the pins are compatible, I just want to make sure I'm not missing...
My nRF52840-DK stopped working. When trying to connect using nRF Programmer v2.2.0 I get the following in the log:
15:45:05.011 Using @nordicsemiconductor/nrf-device-lib...
Hello,
just recived this kit, I ordered it some time ago but were no stock.
Problem is that software doesn't detect the hardware under "SELECT DEVICE". The device has...
When flashing files from an iOS device I run a lot into data size errors (not always), when using the same files on Android they can be copied without a problem.
It looks...
Hi,
I built a ble_app_buttonless_dfu_pca10040e_s112 project on the nRF52805. However, I cannot receive Bluetooth signal on nRF connect.
I have attached my generated hex...
Hi,
In an application with a nrf52840, we measure the frequency by counting rising edge with PPI linking GPIOTE EVENTS IN and TIMER TASK COUNT
GPIOTE.EVENTS_IN -> PPI...
Hello everyone,
I created my first own layout design and the antenna. Before I order the PCB I hope you guys can review it one time. I tried to get the most informations...
Hi all.
As per subject, I'm unable to follow device using PCA10040.
Everything was set according the latest documentation available ( infocenter.nordicsemi.com/.../nRF_Sniffer_BLE_UG_v4...
To the kind attention of Nordic support team,
we are planning to use nRF5_SDK_17.1.0_ddde560 and nRF52820 for a project. We are interested in using gzp gzll library compiled...
Hello
I'm working on a project inspired by the ble_thread_dyn_mtd_coap_cli example and for which I added the management of BLE LE Secure Connections (inspired by https:...
Hi all,
I observed an issue after upgrading to 1.8.0 and to Zephyr 2.7.0-ncs1 respectively. When having Zigbee (and NET core) enabled, all images are built as before. The...
Hello there,
I've set up 1.RaspberryPi with an otbr docker container.
Thanks to Sigurd I have set up 2.nRF21540DK running CoProcessor firmware built with nRF Connect SDK...
Hi,
I want to know more about composition data size. As I have read in Mesh Profile v1.0.1, composition data page 0 is mandatory, while the other pages are optional. The...
I have custom board defined in DTS file. There will be multiple variants of boards, therefore I need to check which board is selected. How to check which board is selected...
