Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hi there,
I am trying to obtain a .hex file for my project for Release Configuration. I don't see the .hex file get updated in the pca10040\s132\ses\Output\Release\Exe directory...
I am a electrical engineering student in my final year of study and am developing a product for my final year dissertation.
The project idea is to help identify sickness...
Hello,
I am using,
iPhone 7
iOS v14.8.1
nRF Connect for Mobile iOS v2.4.13
I have used nRF Connect for Mobile on android which shows this menu when peripheral...
I am using the NRF52840-DK and using the Zigbee light bulb example.
1. The DK board successfully connects to the zigbee network - Z2M in this case.
2. I have added an...
Hi everyone, my colleague developed a firmware using Arduino Nano 33 BLE and PlatformIO. Now I have to rewrite the code using Segger Embedded Studio. The problem is in the...
Hi there, I am developing a peripheral to central system with nrf52840 base on NUS service. Now I tried to increase the MTU of the peripheral to 247 to increase the transfer...
Hi,
I am using NCS for development and configuring GPIO pin as input, but I found the GPIO can't configuring as NO-PULL mode. There are only two options: Pull up and Pull...
Hi,
I am working on ble_bms_app template. While the nrf52840dk is connected to laptop, I don't get JLINK connected notification on the desktop. Sometimes i get the connected...
Hello.
I'm using nrf52832 (S132 v7.0.1, SDK v17.0.0) to develop peripheral roles.
Setting UUIDs for advertisements, services, and characteristics. At that time, sd_ble_uuid_vs_add...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0) as central and Android device (Bluetooth 4.2) as advertise. Android devices use nRF Connect.
I can set...
We are aiming at a low pin count interface between modules. Ideally we would like to use the programming pins for both programming and as an I2C interface. Is this possible...
Hello,
I am new to Nordic, Zephyr and Linux. I have been going through the "getting started guide" on the zephyr docs website and ran into this problem not being able to...
I heard that nrf52832 rev3 has been released. Our product is using nrf52832 rev2, nrf SDK 15.3. If we change the chip to rev3, can we use the firmware without modification...
