Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello.
I have couple of questions for hardware parts location on pcb with nRF9160.
Q1.
I'd like to ask a better location for eSIM(MFF2) related nRF9150.
This...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
In an effort to fix Toolchain problems setting up nRF Connect, I uninstalled Python and tried reinstalling via choco install python as per the "Installing Manually" instructions...
Hi,
Please fix this bug: The DK device is no longer found after following the following procedure
Problem operation process emerges
windows:
DK:PCA10090 0.9...
Hello,
I started my prototyping with the 52840DK and the SD Card was working fine. However, with the 5340 dev kit, I cannot get the SPI to work and access the SD Card properly...
Hi,
I connected my nRF52840 dongle to the laptop, it was detected with a red LED glowing on and off. Later I installed the nRF Connect software and installed the Power...
In our nRF52832 application, we have an external 32.768KHz crystal as the nRF52832 low frequency clock source. We also have a 32.768KHz oscillator on the PCB that is used...
Hello,
There seems to be a bug with scanning for many Bluetooth advertisements while simultaneously sending data over uart in Nrf sdk v17.
I have tried to work around...
When loading the nRF Connect Plugin for VCS, I am receiving either a crash message or the message below. It looks like a Python syntax error in the kconfig extension. python...
SDK 17
Soft device 7.2.0
nRF52840
Started with the 'fatfs' example, updated it to allow uninit, and to not reinit the IO if init is called multiple times.
it's working...
Hello everyone, I combined work with a timer and an example from ble_app_aurt pca10040 s132, the problem is that the timer does not work evenly, yes, I know about the low...
dev environment segger embedded studio with nrf5 sdk
I have separated my project source and the paths of nfr5 sdk the project have different folders for different drivers...
I'm using led1 alisa for indication that network core is runing. But if I compile program, variable is not initiated from DTS. It looks like compiler does not init dtLed variable...
Dear Nordic,
we are developing FW based on nRF52832, SDK 17.0.2. We have 2 devices: BLE Central with SD S332 and BLE Peripheral with SD S112. The Peripheral is basically...
