Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I use a 52832 as the central device, a 52840 as the peripheral, the two established a connection for a period of time,(After a period of time (approximately 30s), there is...
Hi
I am evaluating nrf9160 with an nrf9160-DK on nb-iot in Greece. I am using the asset tracker application example.
I have an issue of DNS not resolving that is expressed...
I am using NCS v1.7.1. I am developing a custom application on top of 802.15.4, which is based on the 802.15.4 PHY test application.
The problem I am facing can be demonstrated...
Hi here,
I m working with a medical device which should probably have to be certified IEC 61508-SIL 3.
I m still new with that certification process, and wondering if...
Hi all,
I' am sending data from nrf_52840 through zephyr to nrf_connect_app for mobile, iam sending data in decimal format(uint_8t) but iam receiving it in hex,
what can...
Hi
The power profiler app can't find PPK2 after update nrf connect desktop and power profiler.
The programmer and Bluetooth Low Energy app also can't find nrf52dk after...
Hi,
I'm trying to use ble data instead of cli terminal. when nRF52840 received data from ble, I want send the data to cli instance. I called function named "void nrf_cli_print_stream...
Dear Team,
I'm using a custom board to test a radio module based on the nRF52840 chip, in this board the P0.24 pin is tied to a led that blink during the execution of an...
The poly1305 implementation is only covering the obsolete RFC 7539 which got updated by RFC 8439
https://github.com/nrfconnect/sdk-nrfxlib/blob/main/crypto/nrf_oberon/include...
nRF Connect SDK v1.7.1 sample \ncs\v1.7.1\nrf\samples\bluetooth\mesh\light_ctrl\
Long transition times fail due to a 16bit value which needs to be 32bit (I believe, can...
Question regarding nrf5340 ADC input tolerance
If I power the nrf5340 from the VDDH pin at 5V, will the ADC input pins be able to read up to 5V then or just 3.3V?
Thanks...
We have a product that uses the nrf52. Due to availability issues I need to port that project to the nrf51822. Since the nrf51 supports up to sdk 12.3.0 what is the best way...
Hello All,
Thank you in advance for your time and interest in this issue and willingness to provide suggestions.
We have a product that uses the nRF52832 processor in...
Hello,
I'm trying to connect a sensor to the nRF9160 board using the example Asset Tracker v2.
My sensor (SHT30) is connect in I2C to the pins 31 (SCL) and 30 (SDA). In...
