Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
Does nrf9160 support C++? If it does, which version? I saw a similar question over 2 years ago in which C++ was not recommended ( https://devzone.nordicsemi.com/f...
SDK: v17
Softdevice: S112
I am currently checking the throughput using nrf52810 or nrf52805.
In device A, data is input as Uart and checked as device B input data...
Hello everyone! I want to evaluate the exact power consumption from the camera (Arducam Mini 2MP OV2640) using the nRF52840-DK as well as its SDK with the nrf52-ble-image...
Hi,
I am trying to implement USB DFU on a NRF52833 with nRF5 SDK for Thread and Zigbee v4.1.0 and nRF5 SDK v16.0.0.
In a first step I want to perform this on the devkit...
Hello,
I have several issues with the new nRF Connect for VS Code SDK, I put them into one ticket, although, some of the issues could be related directly to nRF Connect...
Hi
1: According to this ticket: https://devzone.nordicsemi.com/f/nordic-q-a/28335/nrf52840-usb-pins-impedance you recommend to not
have any serial resistors on the D...
Hello!
I have installed Android nRF Mesh application version 3.0.3.
Also I bought Yeelight YLDP10YL lamp which is qualified mesh product ( https://www.bluetooth.com/learn...
Hello,
I am getting a bit lost in the pool of different versions and libraries. For simplicity, I just want to achieve a single goal to start which is send a bluetooth packet...
Hi
1、 I want to know the connection mechanism of one Central connects multi Peripheral.
2、What is the time interval between one connection switching to another? Is there...
Hi Guys,
i am using nordic nrf52840 controller. and i have my own bootloader application code.
and once the controller boot up then it start mbr code from 0x00000000...
Dear Nordic Team,
Is it possible to have dual role (one at a time) on nrf52805? Is any such stack available?
I am very new to BLE and i am facing a problem in BLE Uart...
Hello Everyone,
I am a beginner for working on Nordic devices. I have one query. I have to build a firmware in NRF52840. Now 2 different apps will be connecting to this...
Hello
I am using 5 nrf52833 dev kits and the ble_zigbee_dynamic_light_bulb_eddystone example from nRF5_SDK_for_Thread_and_Zigbee_v4.1.0
I have modified the following...
I'm trying to achieve a low power operation on a device which has a nRF52833 module with a SPI peripheral on Zephyr. It is based on the peripheral_lbs.
The intended behaviour...
