Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi. I would like to know how to do a DFU over UART using a custom desktop application (without using nrfutil command nor nRF Connect app). What would be the UART protocol...
Hello,
I have the same problem as this topic: https://devzone.nordicsemi.com/f/nordic-q-a/77267/nrf9160-azure-iot-hub-on-thingy91-mqtt-connect-error
I'm using nrf Connect...
Hi,
We are trying to use our NRF91-DK with a proximus simcard (belgian provider). I'm trying to get the https-client example to work without any code modifications. We know...
Hello,
[this question is related to this other question ]
I am using the nRF9160 SoC, the modem has firmware version 1.3.0 and the Nordic SDK is v1.5.0.
My goal is to...
We have this unit with an nrf52840, it suddenly refused to respond to `nrfjprog --recover`.
This is the second unit this happens with.
The power seems ok (we can see on...
Hi Team,
I am using nrf52833DK, nRF5 SDK for Mesh v4.2.0 and nRF5 SDK v16.0.0.
I am trying to implement mesh DFU, but the DFU is stuck at the 35th segment. When I probed...
Hi,
I want to use UART to send and receive data, so I refer to ble_app_uart example to add the UART function to the ble_app_hrs_freertos, but I found it returns error...
Hello,
I am currently trying to get a slightly modified version of the blink example from zephyr to work on the nrf5340.
As you can see below, I am starting two threads...
I want to use the OTP register for production, but I don’t have permission to read the contents of the OTP register。
The following are my steps:
1.Allow the UICR area...
Hi,
I have a question regarding the nRF5340 Development Kit.
I use nRF5340 in the BLE Central role, I'm using a similar code like in the example central_bus.
Sometimes...
We have noticed that generating LE Secure keys [ nrf_ble_lesc_keypair_generate() ] takes 2.5s. That causes our external, 1s watchdog to trigger. Is there any way to improve...
Hello,
I was going to email my local FAE about this, but figured I would post it here for anyone else who may have the same/similar question. To preface, I have reviewed...
Hi,
Of late, I've been evaluating Zephyr in its support of the nrf5340. I've come across several deficiencies that need to be addressed:
1. All callbacks (for the most...
I have an application for NRF5340 which I was trying to add BLE HCI RPMSG into the network core. I went ahead adding the necessary build configuration in such a way I would...
