Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Dear Support Team,
I’m using nrf52840 with PCA10056 and SDK 14.1. I want to make a DFU feature using SPI as its transport layer. Could you please help me about the following...
Hi
There is an issue in SDK for Thread & Zigbee 4.1.0 release. It does not appear in previous releases. The problem manifests itself as higher current consumption. According...
HI,
I want to make a test dongle by using Central_hid project in NCS V1.5.1
Now my keyboard can pair with dongle1 and works well, then i read out the code in dongle1,...
Is there a good example for using direct test mode, with an nrf53 and using an external xtal?
What application mcu code to use? And does it enable the LF xtal pins?
I am trying to run the ble_app_uart_relay example found at: https://github.com/NordicPlayground/nrf52-ble-app-uart-relay . I know this was made with sdk16 but I would like...
HI,
I need to work on external flash memory which is placed on Nrf5340. I need to know where is the sample application to know the interfacing basics and I need to know...
Dear Support
I'm new on ncs.
Now I've read nrf-connect-sdk-tutorial and I can build a project with SES.
I want to automate the build,
So I test
west build -b nrf9160dk_nrf9160ns...
i have look for many DFU examples in NCS1.5.0 , but samples are Abstract ，and can not to start . a ble test app in phone have a menu that can send file to nrf5340 through...
I use our designed board with control chip nrf5340 to test ncs1.5.0 sample peripheral_uart , I not changed a word of sample .but when debug program, show :Not able to allocate...
I am just getting started. When I use the SEGGER / file / open nRF Connect SDK Project and try to configure for a SDK release 1.5.1 (/opt/nordic/ncs/v1.5.1), toolchain version...
Hi,
we are bonding an nRF52832 (SDK version 17.0.2, Softdevice S132 7.2.0, using the Peer Manager) and nRF Connect (Desktop, version 2.5.1) using numeric comparison method...
Hello,
I have a question about the text_record sample, I have a thingy91 and I would like to read the device with NFC on my phone. I saw that this sample could do that....
