Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi Team,
We want to write our own MAC address on nRF52840 module. It's a production level MAC address i.e. it is fixed MAC address cannot be overwritten. What is the procedure...
Hello,
I am using SDK 14 & nRF52832 & peripheral role; I have setup a timeout in the order of several seconds, and during this time my device shall advertise but reject...
Hi,
I'm using nrf52840 and trying to define the pin mappings for my custom board. In order to do this I'm studying the board definition of pca10056 (pca10056.h).
In...
Hey all, I'm trying to run the node cli flash "imei" -f /path/to/firmware.hex command on the terminal. It prompts as ERROR flash <deviceId> failed!,
ERROR Error: No such...
Hi
I'm working with version v8.6.90 since the master version at this date have an Auth amplify issue.
The Fetch function on the map is buggy :
Here is the Chrome dev...
We are using nRF52 SDK 17.0.2 s132_nrf52_7.2.0_softdevice.hex in our application. When entering in DFU mode from application, we perform nrf_power_gpregret_set(BOOTLOADER_DFU_START...
I am willing to use nRF52832 chip in one of my project. But all the breakouts dont fit the size and I want to design my own PCB with i2C accelerometer. I only want to transmit...
Hi,
Corect me if I'm wrong, but the initiation of ble_gap_addr_t.addr_type in main.c in the HRS_C demo is not necessary, as the addr_type is calculated based on the address...
Hello Folks,
I am following below steps to add Zigbee FOTA to Zigbee: Light switch example.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_zigbee_configuring_libraries...
Another problem is that when I turn on I2S to read data, the while loop does nothing, and the broadcast can't be transmitted, just like I2S has occupied all the CPU, and other...
Hi Devzone,
I use original mqtt_simple example to test connecting with MQTT Broker.
I ran it on Ubuntu, SDK v1.5.99. When I press button to publish message, some errors...
I'm planning to evaluate AoA and AoD using nRF5340 DK. I asked my local RSM about getting the antenna array and was advised to get nRF9160 DK.
After reading the documentation...
I have a sniffer working . I Have a bouad with
west build -b nrf9160dk_nrf9160 .. If I start an example on the zephyr-mainline hello it work I see in ttyACM0 the printk...
I am running the usbd_msc example in nRF5 SDK 15.2 and trying to eject the disk on Windows/macOS.
But, USB MSC drive sign kept being visible in my explorer. Is there any...
Hi
I'm using nRF Connect SDK v1.5.1 and Segger IDE. Starting from fresh with Clean Build Directory, the sample won't compile with Segger IDE (build solution).
I aware...
