Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Dear all,
Pushing the hardware to the limits, I came up with a question about the architecture of the microcontroller itself: Can two different instances of SPIM start...
Hello,
I am experiencing some strange behaviour through DFU process when build with GCC -O2 optimisation.
The upgrade process seems to complete successfully but after...
I got a device with a secure bootloader, but I lost the private key and the firmware got corrupted somehow. Is it possible to flash a new bootloader via BLE or is it bricked...
I am trying to understand the following, hopefully someone can explain:
AFAIK, BLE advertising is stopped as soon as the limit of the SD is reached, AKA the PERIPHERAL_LINK_COUNT...
Hello, I am I'm a novice at developing NRF 51822. My Development Environment sdk : 12.3 IDE: KEIL v5 SoftDevices : s130
It's being developed in this environment. Q1 .NRF...
Hi. I am struggling to build the DFU secure bootloader example for the n52 DK development kit. Using SEGGER embedded studio.
I get the following error;
cannot find .....
Hi Support Team,
We bought the nRF52 DK along with the PPK so we can measure current consumption of a DUT. It was working on the power profiler App in nRF Connect and we...
I am starting up with nRF52840, currently i have the dongle but expected to receive my DK in the next few days. This is my first BLE project, so i started reading a lot of...
We have a BLE peripheral implementation using the nRF52832 and both the S332 v2.0.0 and v7.0.1 softdevice. We are supplying the LF clock to the nRF52 from an STM32 MCO output...
Hi,
I would like to set up a couple of boards communicating over Bluetooth; I was hoping someone could provide some pointers.
I would like to connect the nRF9160DK to...
Hello, i'm trying to get usbd_msc example to work on custom, test pcb, with Microchip SST26VF064B flash chip (SDK version 16). As previously advised, i have redefined NRFX_QSPI_PIN_xxx...
Hi,
I wanted to setup a dynamic buffer but I don't have any leads on how to set it up.
Basically, i want to store a stream of data every time it is recorded and then send...
I know this has been asked a couple of times, but I haven't been able to find a straight forward answer.
I have a GPS module that spits out data via UART (no flow control...
Hello, Team.
I always thank to you.
I tried to find some information, but it is a little bit hard to find, so I upload this Q&A.
Now I'm interested in Mesh protocol...
