Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
When I open J-Link RTT Viewer application to see logs of a program with set CONFIG_LOG_BACKEND_RTT , then I see logs' output with some delay, comparing to logs of the same...
Hi.
Can you make a youtube video showing how to use SEEGER studio for a demo project.
I would like to see the whole workflow starting with a new project for nRF91xx where...
Hello,
I'm developing an HID consumer control application with the nrf52832. As many ble products have, I would like to add a power off button to my pcb. Is it better to...
I'm just after C headers and Makefile like the NRF5 SDK.
All I found was some "AppImage" file for x86_64 which I've no idea what to do with - I tried unzipping it, but it...
Hi!
Whenever I open an example for the nrf52833 (PCA10100) in SES I get the error "The evaluation period for this release has now expired". This does not happen when I try...
I am working on nrf52832. For my task, I need to knoow how nordic find out the Total average current on Online Power Profiler for BLE( https://devzone.nordicsemi.com/nordic...
I wanna try to connect multiple device with only one Android, but I don't know how many devices Ble can connect to only one Android. When I try demo on Samsung galaxy S8,...
Hi,
I have an issue that is urgent for me, as we wish to add DFU capabilities via pre and post production hardware. I am using Android 10 on Samsung Galaxy A10 to test...
Hi,
I was able to create a device driver support for a DAC, model TI DAC80501Z. In the first place I put the driver in zephyr/drivers/sensors.
I works fine.
Then I made...
Hi Team,
Please provide the nRF52 based module Characterization, software testing for FCC/IC/ETSI certification test procedure and document
Is DTM test enough for FCC...
According to SDK documentation for GFX library :
“After generating a font, you must change FONT_INFO::height to be described in bits (pixels), not pages”
But in the provided...
Hi,
I can build the blinky_pca10040_s132 example and I loaded it in the nrf52840-DK without errors but nothing happens in the bord I can´t see any lead blinky.
Please...
Hi
We are sending devices for RF/wireless testing and need test firmware that allows for the Bluetooth frequency and transmission power to be easily adjusted. Does Nordic...
Hi.
As you have made a progress in your development of both hardware and software. It would be greate if you remove old videos from youtube. I have just spent some time...
Hello.
I am using nrf52832 and Segeer Embedded Studio.
I want to add a timer function to the ble_app_uart example so that the sensor value is read every 50 ms.
So I...
