Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi,
So I was having an error which caused my application to stall in the "do_stop_check" part of the nrf_drv_twi.c file, so I added a bit of code to check if I could figure...
We have a device with the following configuration:
nrf5_SDK_for_Mesh_v3.1.0
nRF5_SDK_15.2.0
s140_nrf52_6.1.0_softdevice
mesh_bootloader_gccarmemb_nrf52840_xxAA ...
Hi,
I'm trying to make a script in Python using the nRF52840 dongle, to make some BLE advertising.
I'm using:
- Python 3.7.2 (32 bit)
- pc_ble_driver_py library
...
Hi everyone,
I'm using ses IDE to debug via J-link on nRF52840 DK.
I'm debbuging CDC ACM example ( I haven't changed it ) but when I debug: ret = app_usbd_cdc_acm_write...
I am designing a PCB for the nRF52833 aQFN chip. To reduce the cost of the PCB I would like to fanout the inner row of the IC package on a single layer by using 3/3mil traces...
Hello,
I have a certificate attached, but in my personal account it gives an error when I enter the DK data.
Please tell me why the error occurs?
OS: macOS 10.13.6 ...
Hi,
I am using IM69D130 MEMS sensor with nrf52832 I just want to confirm the output of pdm sensor . please any one suggest how should i proceed . how do i code for it ?...
I am attempting to migrate my BLE project to a higher security level with bonding. Was mode 1 level 2 and am upgrading to mode 1 level 4. When I change the configuration to...
Nrf52832 chip is used, and the software package is the “nRF5_SDK_16.0.0_98a08e2” version.
According to customer feedback, Bluetooth connection is generally unstable...
Hello
I've seen several places that it is posible to build the project using jenkins, and hook Jenkins to the git repo where our nRF sourcecode resides.
Unfortunately...
Hi,
I am testing the USB CDC with nrf52840 and I want to receive a predefined array of bytes over USB serial every time I send a specific array of bytes.
Just a simple...
hello i am using sdk 16 with nrf52832 i am thinking of using zephyr with nrf52832 and have no idea what is zephyr and uses of zephyr other than that it is testing tool
1...
I have older files that were compiled and working fine with the older versions of SES, SDK and now I’m trying to figure why they don’t work with the latest version, that is...
