Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi,
For my home Mesh network, I use a Android mobile phone + nRF Mesh App as a mesh provisioner to configure the nodes, and control the mesh node as well.
There're about...
Hello，
When I use the nRF9160 to upload the data to the cloud based on the LTE-CatM1, what's the maximum current? The datasheet of nRF9160 mentioned:
1. Application CPU...
Hi all,
I'm struggling with UARTE and easyDMA. i just want to send data with TX.
I am trying to configure it with the hal librairy but i cannot manage to make it work...
Hi I would like to, at app level, implement access control to characteristic. My characteristic is configured solely as notify (no read, no writing).
When a smartphone turns...
I am testing about tx power level on nRF5_SDK_15.3.0_59ac345 with nRF52840.
I have some confusing about sd_ble_gap_tx_power_set() function.
In peripheral advertising...
Hey guys I want to resolve some issues regarding RSSI values received from BLE beacons. I have ibeacons type.
1: Ibeacon format says the last byte is signal signal, is it...
Hi, after following the tutorial about building the asset tracker firmware I came to the problem of generating merge.hex file. The zephir.hex file is generated, but the merge...
chip: nrf52840 aQFN package
5~10% of the products were defective. by causing analysis, There are short some pins bottom of chip.
I already read this guide after this...
Dear All,
I am using the NRF51822. I downloaded All the latest SDK and Segger Embedded Studio. No matter which sample project I choose I get the same error.
C:/Nordic_Semi...
hello,
please guide me to active LTE in Iran. i used several modem firmware release and can't connect to the network. im using nRF9160 DK and testing with AT sample programmed...
The Nordic Uart Service example in SDK14.2 with SoftDevice 5.1.0 appears to use Write Request judging by the timing which limits transmission to about 30mSecs per packet with...
Hi,
We're using the Android BLE library from Nordic. It really helped us handle a lot of the things we didn't want to think about handling on the bluetooth stack. (Thank...
Probably frowned upon but like being able to work from raw datasheet, so I know that I can. So given that the datasheet would suggest that changing a GPIO pin to be an output...
Hi,
On latest SDK (15.3)n nrf52832, PCA10040, on ble uart bare example, I get a bug when stopping advetising:
line 659: "p_advertising->evt_handler(p_advertising->adv_evt...
Posting this in hardware because it seems like the most appropriate...
We are conducting some localization experiments where we will be capturing advertising packets of...
