Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
iPhone11 + iOS13.1.2 cannot connect to nRF52832 based IoT device when application is running in background. iPhoneX + iOS13.1.2 can connect without problem. Does anybody tested...
So I recently purchased an nrf52840 pdk and was following nordics getting started guide. however my pc will not detect my board when i plug it into the usb. When i plug the...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hello,
I'd like to use a central_peripheral example project (sdk 15.3) : Experimental: ATT_MTU Throughput Example
What does it mean that an example project is experimental...
Hello,
I have a problem with using the FDS library.
I started by exploring the example CLI program (examples\peripheral\flash_fds), it seemed to work as expected.
Then...
Hi
I have a nRF52832-DK based central node and multiple nrf52832 based peripheral nodes implemented using a combination of ble app uart c + multilink central at the central...
Hi Guys,
I am trying to access the serial number written on MCU through software.
White strip on MCU has details such as PCA10056, 1.0.0, 2018.04, 683xxxxxx. I am trying...
The Qorvo QM14501 LNA in nRF9160 reference schematic seems to be consuming several mA of current, which is quite a lot for a GPS LNA. There are other LNA chips in the market...
Hi
When I use the nRF5_SDK_14.2.0 of nRF52832, the example is selected ble_app_uart. And the Android example is the Android_UART_Client_Bluethoot_Sensor_Nordic_CortexM4_NRF52832...
Dear team, Device - nRF52832 SDK - SDK_15.0.0 IDE - Segger Embedded studio Softdevice - s132_nrf52_6.0.0 I am doing buttonless DFU in my application. I have successfully build...
Hi,
I want to use uart. I configured two uart, uart0 and uart1. I want to read and write to one uart using APP_UART_PUT and APP_UART_GET. how it possible without uart event...
I am trying to modify tx settings in open thread but when I try to execute otLinkSetMaxTransmitPower it cannot find this function. It seems to find all others. Is this not...
Hello,
I'm using a nrf51422_xxac_s110 chip, with the 12.3 SDK. My code is based on the ble_peripheral\ble_app_uart example in the 12.3 SDK. I'm hoping you can provide some...
Hi,
We believe we have either a BT communication issue for Nordic Semiconductor ASA NRF52832-QFAB-R
https://www.digikey.com/products/en?keywords=1490-1055-1-ND
...
