Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
I am trying to get started the pc-ble-driver-py tool. What I would like to do is perform a scan for available BLE devices, connect to one of them, then write to a characteristic...
Hi guys,
to process the NFC data sent from a smartphone to NRF, I use the " nfc writable ndef msg example" . However, the issue is that I cannot find a variable where the...
I'm using a timer to read the ADC repeatedly using PPI. On ADC read finish I call nrfx_saadc_buffer_convert ready for the next timer event. However, if I want to cancel conversion...
Environment:
SDK v15.2.0
Raspberry Pi 3 (as a border router - Jessie).
MQTT broker in Linux PC (Mosquitto)
nRF52840 as a MQTT Publisher.
Without TLS-PSK, MQTT...
Dear all,
I'd like to re-init sd-card when detect it plug/un-plug. But i face a issue when i re-mount sd-card it can not open file....My flow as below
what is the best...
I'm extending an existing central application to support extended advertisement and CODED phy support. However, I have trouble connecting to a device advertising with CODED...
I am using nrf52832 with sd 6.0 and sdk 15.0. My application is based on the buttonless DFU example, and I am using a bootloader with OTA DFU. To update the application I...
Hi,
We are planning to finalize NRF52840 part for IoT project and below are the features/criteria that we are looking, Kindly confirm whether below features will be supported...
Hi,
I've recently hit an issue where sd_ble_gatts_rw_authorize_reply in my code returns INVALID_PARAM when I try and write a long set of data to a characteristic using...
Hello,
I am using the PCA10040 DK, and I want to get a 8 MHz OR 4 MHz clock output from one of the GPIOs.
I've followed the instructions from here
and it works.. however...
Hi there,
I’m trying to find the path-of-least resistance to get the GPS working in the Asset Tracker demo on a PCA10090 (v0.8.5), and I noticed that one of you engineers...
Hi, I am wondering if there is a way to reject Bluetooth pairing with Nordic peripheral outside of my own mobile application. For example the Fitbit devices will reject connecting...
In documentation:
Libraries > Serial interface > Serial interface library > Serial commands > Serial command groups > Serial command details > Access Layer Model Pub Period...
In following this example: https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development-kit/posts/scheduler-tutorial
once I added
APP_SCHED_INIT(SCHED_MAX_EVENT_DATA_SIZE...
Where do I get the output (from the main apps printf/printk etc) from the Thingy:91 once it's connected via 10-pin swd-cable to my nrf9160 DK?
I don't think there's anything...
