after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
hi,
i am trying to integrate nRF SDK 15.3's ble_app_buttonless_dfu service in ble_app_blinky example,
after adding all source files and and preprocessor definitions while...
Hi,
we are using a custom nRF52840 board with SDK 15.0 and softdevice S140 6.0.0. Flashing the application including DFU and softdevice using SES produces the following...
I have a strange problem running the CLI example in the DK on the Nordic dev board with SES: It works fine with build/run, but when trying to debug it pops up a message that...
I am using the nRF52832 in several projects for several different clients. I have created a "project" under Visual Studio using VisualGDB for each one, using the automated...
Hi,
I would like to know how to raplace a MPU-9250 chip with ICM-20948 in a Thingy:52 circuit.
Let me first state that my electronics engineering knowledge is at hobby...
So I've had a LOT of problems getting power management to work with UARTE on the 52840. We're using both UART_0 and UART_1 and have finally gotten UART_0 to work as it should...
When attempting a DFU update (containing APP + SD + BL) with the android version of nRF Connect, it appears that connect will update the device's application even when bootloader...
Is it possible to pass a memory location to PWM (preferably via DMA) via PPI. This is a sound project and my intent is to update two 8 bit PWM outputs at 44.1kHz. I typically...
Hi,
I am working on a project and I want to program the nrf52832 with the arduino IDE with this package ( https://github.com/sandeepmistry/arduino-nRF5 ). I want to use...
Are there any restrictions (eg, timing) or issues for using different references for different channels in Scan mode?
eg
AIN0 uses VDD/4 as reference;
AIN1 uses VDD...
Hi All.
Do someone know what is the oversize I get when I use the FS_storge example to store data on the interanl FLASH.
FOr every bulk I open (id+key). How much bytes...
I'm using nrf51822 and SDK 10, S110 Softdevice. Implemented whitelist using device manager and bonded with single device , after bonded my device with phone (using nrfconnect...
I'm using nRF51822 and SDK 10 , Softdevice S110 . I enabled whitelist option in my application its working as expected, but when after device is resetting peer device data...
Hello,
I am working on an application on a nrf52840 using soft-device 140 and SDK 15.3. I have written 90% of the application using the ble_app_uart_c as a template for...
Some context: I am using an nRF51 with SoftDevice S130, which acts takes both central and peripheral roles, and uses UART to communicate to a peer MCU. I am currently facing...
