Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
I have a simple central device where a gpio triggers the device to scan and connect to a peripheral. This is running ok on the PCA10040, and also on a separate hardware platform...
Using the latest version of Bluetooth low energy (V2.2.1) running on nRF Connect V2.6.2 I was never able to connect to a peripheral device.
The peripheral devices are based...
I'm using Nrf52840 as the MCU for my circuit board, now I need to use it to transmit audio data which is 16bit, 16KHz PCM format(mono channel, therefore 256 Kbps) to the external...
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v11.0.0%2Ftwi_master_with_twis_slave_example.html
Testing
Test the TWIS slave and TWI master...
I followed the steps in Getting Started Assistant to load the asset_tracker application using SES(4.16) and it fails with the following error.
CMake Error at /Users/myfile...
Hello,
For ble communication in an application, I am usnig NRF52832 based boards. I am using ble_app_uart example for peripheral and ble_app_uart_c example for client. I...
I am using the nrf51422 development kit with sdk11. I am running the proximity application for the battery life service. I am inputting voltages ranging from 3000 millivolts...
SDK14.0.0/S132 5.0.0
The SDK provides an example of turning on SSP Debug mode for LE Secure connections
Is there a way to enable SSP Debug Mode for BLE Legacy Paired connections...
Hi , I have some issues with the ADC. When moving in and out from low power mode the ADC isn’t working correctly. I am using the nrfx_saadc driver. When moving to low power...
Hello Nordic Team,
I am using nRF52840 Dongle (PCA10059) and nRF5 SDK. I was tring to use PWM example code (PATH - "nRF5_SDK_15.3.0_59ac345\examples\peripheral\pwm_driver...
Hi.
I build application which is mix of writing QSPI to external NOR FLASH, using linkage list base on the fstorage FDS example all in the embOS (RTOS of Segger).
I have...
Hi all,
I using nrf52832 and segger IDE
I am trying disable softdevice and enable it while chip running. In my project, I use RTC1 for app timer.
When I disable SD,...
My setup:
- nRF52840 Preview DK (though i have tried this on a newer version too)
- 3.3V separate supply
- DMM (Agilent 34465A)
DK Connections:
- SW9 is set to...
Hi,
We are trying to take the nRF sniffer trace but there is some issue is showing , i will explain it below.
we are following nRF Sniffer "User Guide v2.2" for initialization...
Hey,
So I recently got some test SIMs from AT&T to use for our development. I'm trying to get them working with my nRF9160 dev kit but can't seem to get a connection to...
