Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi
in my test bench for system validation I would like to control the system based on nRF52 via Bluetooth to speed up testting of various samples.
It seems that there...
Good day.
We recently bought the NRF52 DK and the Power Profiler Kit with the intent to log power consumption of our battery powered products. Before purchasing the products...
Hi,
I tried nrf connect and nrf hrs example. I used nrf52DK. I bonded the device, and connected with autoconnect. I turned off the nrf 52 DK, and turn on. The nrf connect...
I am using the secure bootloader with DFU, and the buttonless DFU service. I extracted these applications from the Thingy SDK v2.1.0. This works perfectly fine as long as...
Hi,
My problems are as follows:
SDK :nRF5_SDK_15.0.0_a53641a.
IDE:MDK 5.2.6
Chip:nrf52832 SPI0
External Flash :W25Q64
Now ,I can read the chip ID correctly ,but...
Hi,
Please find following source code.
After compiler by Keil 5.24.2, some code will not compiled,
I can see the situation by "enter debug mode, please find following...
Hi,
I am trying to develop a central device that would scan for devices that start with a prefix XYZ_, for example XYZ_1111, XYZ_1245,...
Is there some way to add a name...
Hi,
I am using esb function to implement my project, and I set "noack" condition to "true".
How can I know the destination address when I receive a packet?
Thank you...
I need to add ARM_MATH_CM4 to my preprocessor definitions using Segger Embedded Studio.
I know this has been dealt with in "nRF52832: How to Include the "arm_math.h" library...
We are developing a BLE device that will act as a central and send data to a peripheral. To begin with, I have used the uart central example code from SDK to set up a central...
Hi, I am trying to figure out the adc example posted by Nordic Semiconductor on Github.
https://github.com/NordicPlayground/nRF52-ADC-examples
There was two examples,...
Say I have the PWM Decoder set to NRF_PWM_STEP_TRIGGERED. If I use NRF_PWM_TASK_NEXTSTEP to step through a PWM sequence, will an event be generated for each step? I would...
Hi,
I have merged ble_app_multilink_central example and ble_app_uart_c example. and function is Ok.
Central(nRF52) can connect to HM-10(ti cc254x) and communication is...
Hello
I am trying to do BLE communication using BLENano2 (nRF52832) now.
Therefore, using SDK 15.0.0, we are writing a program with keil u5.
BLE communication can...
Hello!
I am using SDK 15.0.0 with keil.
I tried to use the sample program to do BLE communication, but I have one thing in doubt.
I'm using SDK15 / example / ble_peripheral...
