Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Dear Sir/Madam,
I want to measure the data speed between two BLE 4.2 based devices and two BLE 5.0 based devices.
Using nRF52 products for this purpose.
Kindly help...
I know that the nRF52832 is strictly a 3.3V device however, I was wondering whether any of the GPIO pins are 5V tolerant?
Is there any internal clamping diodes within the...
Hello,
I have noticed, that https://github.com/NordicSemiconductor/nrfx was updated with a nfct driver. I am trying to extended the nrfx port on micropython (see https:...
Hi,
I'm trying to setup the Peer Manager on a nRF51822 with installed the S130. I'm working with Eclipse where I installed the 12.3.0 SDK.
At compilation time I get the...
Hi, I have a two part question, I know the NRF51822 (and I believe all 4.0 BLE chipsets) are being sunset, when will this start taking place?
Since I'm currently using the...
HI,
i am using nrf51422 with sdk13.3.0 and soft device 130
i am receiving 69 byte of data through UART, i am compressing data in two packets. here after transmitting a...
I have an issue with BLE on Android when using low duty-cycle directed advertising and I'm asking here hoping some people have already seen that issue or something similar...
Hi,
I'm working on a custom bootloader based on the one included with SDK 15.
I have a blocking method (i.e. while loop) that runs at the end of the transmission of all...
Hi,
Some general Nordic BLE device questions:
How to add Characteristic?
How to send data to given c haracteristic?
We are using SoftDevice 132 with Segger IDE.
...
I am trying to free up some RAM on my nRF because I am getting Fatal error 0x4, NRF_ERROR_NO_MEM when I try to increase the size of a 2D array.
I do not understand how to...
Hi there,
I am considering the NRF52840 to build our new platform but I am struggling to find information about how the device Firmware is programmed.
Apart from SWD...
Hi,
I'm using sdk 15.2, with soft device s140 on nrf52840 dongle in peripheral mode. I'm using modiffied ble_app_proximity example. What I wan't to achieve is to set advertising...
I want SoftDevice of Bluetooth 4.2 for nrf52832.
I found softdevice.
15.2.0 nRF5 SDK
15.1.0 nRF5 SDK
15.0.0 nRF5 SDK
14.2.0 nRF5 SDK
etc
Which is Bluetooth 4...
