Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
hi ，i have a problem! how to slow down the update speed when bootloader receiving the pack. my project is base on the SDK 15.2.0,s112 ,secure_bootloader example ,nRF52810
Dear nordic,
i want to create a low power current consumption ADC. i don't need adc value in every time. my need is just take adc value and disable it.
whenever i want...
HI,
I'm currently working with two chips RF24L01+.
Each chip switch in sending role to receiving role several times. By default, I set them in sending role and I whait...
I use sdk15.2 and nrf52832.
I copy i2s examples to nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\ ble_app_hrs ,and nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\ ble_app_hrs_freertos...
Hey all,
So I'm new to the Nordic world and I am having some trouble programming the SoftDevices API. After I compile my code, I get the S112 hex file and try to use this...
Hi Nordic,
I am working on a NRF52 DK with the example code ble_app_interactive. I am using the NRF52 DK as a central and trying to connect to a peripheral hearing aid....
Hi guys. Why the Android Mesh app can not receive the the publish data from the 0xffff address?
As we do below:
step 1 : we use 2xP10040 development kit and an android...
Hey guys,
I'm working on a project and want to build up on the Nordic BLE UART example (mobile device app and node firmware). As far as I know the pairing between the node...
hi all,
I have added the dfu service in one of example of sdk_11 ble_scanner_hrs I followed all help available on this forum and made sucessfuly compiled code but it stopped...
Here is a thing that I want to develop.
As my understanding, if I want to connect with PC I must use the HID example to achieve the event.
However, is it possible that...
I programmed an nRF52 (PCA10040) with the ble_app_beacon sample app and can see it advertising. However the nRF Beacon Android app does not detect it. nRF Beacon seems designed...
Hi,
I have a nrf52840 DK (pca10056) and a nrf52840 Dongle (pca10059).
I am using the following SDK versions:
nRF5_SDK_15.2.0_9412b96
nRF5_SDK_for_Thread_and_Zigbee_2...
HW: nrf52840
SW: nRF5_SDK_15.2.0_9412b96
Hi,
I would like to learn how allocate Flash, RAM and SRAM setting and how do I find out the total RAM/ROM my application...
