Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I have 2 PCA10056 preview development boards.
The newer one (0.11.0 2018.3) works as expected.
The older board (v0.9.0 2016.48) the built-in LED1 thru LED4 do not...
I want to use application board and connectivity board with mesh sdk in nordic chip. Is there serialization is available for mesh like using in nRF SDK15.0.0 peripheral driver...
We are developing an application on the nRF52840 kit with SDK 15.2. We are using Keil as compiler. I have started developmet my application with the example ble_app_cscs....
Hi,
I would like to try the DK in a high voltage mode. I tried switching the power source switch to either LIPO or USB (using LIPO battery and USB respectively) but in vain...
Hi, I'm new to thingy, I want to log the data received and viewed in mobile app / web app from thingy 52 development kit which contains nRF52832. Is it possible to log data...
Hello everyone,
I am in trouble because of a vlotage of current problem, I think it is most a voltage problem.
Let me explain,
I have a NRF51DK that I programmed to...
Hi,
there is no migration guide available for 15.2 , my application currently uses 14.0.
1. when will the guide be available? can use the one for 15.0 till then? will...
I have followed this posting by Hung Bui , with light_switch_proxy_server being combined with the ble_uart.
I am using: nrf52 dk, Mesh SDKv2.0.1, nrf5_sdk_15.2.0.
By commenting...
Hi,
Errata 202 limits the use of vdd as a power source to external components and I, therefore, would like to use a GPIO instead.
My question: is there a need to use a...
Hi,
In my project I am using SDK 14.2 with S332.
I need to change the data in the manufacturer part of the advertisement packet once per second (nearly, timing is not...
Hi,
I have a strange issue. I am reading values from an accelerometer. The read values go into an array which is uint8 and 7 bytes long.
The values are read ok and they...
Hello everyone,
My usb connector is dead on my nrf51 dk, do you know if it is possible to program it without using the usb connector, maybe by using a USB serial port adapter...
Hi!
Does latest NRFUTIL 4.0.0 include mesh update option?
I saw in branch dfu_mesh on pc-nrfutil github that this branch was last updated on 16.12.2016 (nrfutil 0.3) and...
