Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
I'm finding rather high power consumption developing freeRTOS on the nRF52. I have it found that it appears Task's are suspending properly on the main BLE thread (copied from...
Setup
I was just looking through the code in the HIDS module in more detail, now that I have built a few demo HIDS apps I want to make sure that I understand the HIDS module...
Hi,
Is there any other define to change than SERVER_COUNT in main.c of client's light control in order to run the example with only 1 client and 2 servers (instead of 3 servers...
I cannot get the output from the is the example the UART buffer gets filled but there is no output to the tty.
The interrupts seem to be set, but I don't see the interrupt...
Hi
I am using nrf52840 for indoor positioning application based on RSSI. I was wondering if somebody has a tip how to calibrate the nodes before doing the experiment.
Hi,
I'm using sdk12.3.0 ble_app_uart.
My problem is BLE connection.
Sometimes(almost 50%)I tried to connect BLE but fail and I have to connect again.
I don't know...
Hi, I'm contemplating ways to drive a small RGB LED matrix with the nrf52832 in a really space-tight project. Ideally without any external components. I'ts maybe around 40...
Hello,
I need do synchronize the time between two NRF52 devices. One is connected to the other by a custom BLE service. Do you have any ideas how this could be done?
...
I'm trying to integrate buttonless DFU with secure bootloader with bonds with the DFU.
Using SDK 14 with SD 132 v5.0.0.
Using projects: secure_dfu_ble, ble_app_hrs_freertos...
Hello:
When I try to open an example project from nordik, keil doesn't open some files and I get the following error:
"no source": Error: #5: cannot open source input file...
in main() I initialize the timer
// Initialize the clock module
ret = nrf_drv_clock_init();
APP_ERROR_CHECK(ret);
// Request the low-freq clock to start N/A for SoftDevice...
SDK v12, SD130 on 51822.
I init uart through APP_UART_FIFO_INIT, and installed uart_event_handler. UART rx/tx with an external MCU works OK while softdevice running.
...
Hi. I have some nRF51 firmware I'm migrating to the nRF52. It's a peripheral with bunch of vendor specific services, using SDK 13.0.0 and SD 132 v4.0.2.
My code builds...
Dear Nordic,
I am trying to send the sensor data via beacon. I am regularly updating the manufacture data (through which I am sending the sensor data). But while executing...
