after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I'm using the UART driver (drv_uart.c) provided with the nRF5 SDK 11.0.0 on a nRF52 chip and once a NRF_DRV_UART_EVT_ERROR event is received, the receiver seems to be stuck...
Hello all!
I'm researching Radio Notification. I had read define and tutorial . But, It don't make me clearly.
Could you explain more deeper about Radio Notification...
Hi,
I just upgraded the SEGGER RTT source files from V4.98e to the new V5.41b for a nRF51DK project using gcc/Makefile. When linking the (now quite large) program, I got...
Hello,
I am using S110 8.0 soft device and using the example Nordic_UART. I am able to compile the project file in KEIL and flash it onto my board. I don't see any errors...
We are using the low power comparator on NRF51882 RayTac Module (Vcc=3.3V, Vref = 4/8), with which we are making a precise high impedance measurement!
I found some documentation...
I've been sending various BLE addresses to the nRF51 and am getting some inconsistencies of what addresses are being deemed valid.
I am using BLE_GAP_ADDR_TYPE_RANDOM_STATIC...
I am using uVision 5.18a with MDK-Lite ARM toolchain and I downloaded nRF examples for SDK 11.0.0-2.alpha with Pack Installer.
Then I tried to compile " /ble_peripheral...
Hello everyone,
I would like to know, if it is possible to send data (power data) from a NRF52-DK to a Garmin Display Device. Do you know any application, project example...
I wanted extract BLE_GAP_AD_TYPE_128BIT_SERVICE_UUID_COMPLETE that i receive while scanning and compare it with 128 bit service uuid that i defined.
i have seen how ot...
Hi,
I am trying to debug my code in Eclipse using J-Link.
Whenever the code executes vPortStartFirstTask() in vTaskStartScheduler() the debugger stops and I can't debug...
Hi,
is there any simple way to obtain current PWM value if nrf52 PWM module is used to produce complex waveform from RAM array? The task is to get currently settled value...
Hi there,
I am new with nRF52 using SD332 and ANT+. I would like to ask if the nrF52 with SD332 can be configured as ANT+ central and ANT+ peripheral in the same time....
I have a query that is similar to the question below
https://devzone.nordicsemi.com/question/44424/how-do-i-switch-the-target-from-a-nrf51422_xxac-to-nrf51422_xxab-in-keil...
Hi,
We are currently considering the packaging design of a device which will use a nRF52. During housing assembly, the populated, but unpowered, PCB will be exposed to...
Hello.
I have a question.
I use nRF52 and S132v2. I found some programs of nRF51, they use S110, S130. What change does it with difference of Softdevice's version number...
