after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I have a collection of nRF9151 devices using PSM mode.
Each time the application attempts to send UDP data while in sleep mode, they get a detach request (from the network...
Hi
I have two nRF52833 development boards: one is using BLE peripheral_uart, and the other is used as RX (BLE central_uart). My issue is that, with the TX setup being completely...
When a button is pressed during power off, the buttons module disables the wakeup interrupt but the button scan never happens, leaving the module in an invalid state and preventing...
Dear Nordic support,
I was reading the Technical Documentation in the GPIO section for the nRF9151 , and I came across this blurb:
"Note: When a pin is configured as digital...
nrf5340 - running the complete BLE advertising and handling the read / write gatt client processing running in network core and doing rpc to application core
Create a sample...
Hi
I have questions about nPM1300 VOUT1 inductor
1. Our load current for VOUT1 will be <20mA, so could we use below inductor?
2. Datasheet 6.3.5 define it's recommended...
Hello
I would like to use the SPI to communicate with an IC without having a software driver.
I have the following device tree:
& spi2 {
compatible = "nordic,nrf...
Hello,
We are using nrf52dk, with zephyr OS also we have done the setup in VS code with extension.
Toolchain version: v2.9.0
SDK version: 3.7.99-ncs2, these all came...
Dear all,
I'm having difficulties scanning as a central device showing the short /long names like e.g. "Polar H10 xxxxxxxx" I can see the names when scanning on my smart...
Hi,
We recently managed to get the onomondo softsim working on a dev kit, we used the sample code provided by onomodo to do this. Now we want to add the softsim to the nrf_cloud_multi_service...
Hi everybody,
I have problem with my nrf9151-DK and attemp to create PPP communication.
First of all, I have to say that I am a beginner in this matter. I haven't come...
Hi,
I'm new to the nRF52840 and BLE and want to send a simple string like "Hello World!" to a paired device (phone) at a cadance of 1Hz e.g. I started with the peripheral...
Does anyone have experience with using a TP4057 with the nRF5340 for charging and fuel gauging? I watched Adding battery charging and fuel gauging to your nRF52 Series project...
Hello,
I am using the nRF52832 WLCSP with the imprint "N52832 CIAAE0 2207A5", and my FICR reports a codepage size ox 0x400 and a code size of 0x100. This results in a...
Can the nrf7002 be set up to have both a STA virtual interface and an AP virtual interface at the same time?
From all the documentation it doesn't specify that only one...
