Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi,
This question is about 5340. I would like to use SPIM4 instance at fastest 32M speed. According to datasheet this instance needs to use dedicated pin assignments, and...
after building the pc-ble-driver-py and creating v5 lib, we need to build v6.
using WIN 7, python 3.8.
I changed file CMakeLists.txt row 40 to 'set(SD_API_VERS "2; 6 ...
In our Android app, we want to throttle back MTU size when the error rates get too high. However, the app is crashing with NRF_ERROR_INVALID_STATE when we try to send the...
Hello everyone,
I am using the SDK 17.1 with the NRF52832 chip. My current project is created based on the multirole example. My first step was to implement writing and...
Hi Nordic team,
Our requirement is creating two TLS server with same IP and different port no, but when I try to bind two servers only one server is getting bind to the...
Hi,
I have set up the PWM to trigger the ADC via PPI. It works but now i want to verify the exact behaviour by setting a GPIO when the ADC starts a conversion and when it...
Hi Nordic
I want to confirm whether this function pm_peer_id_get will return PM_PEER_ID_INVALID if nrf52833 has never been bound to a mobile phone when obtaining the peer...
I want to speed up the ble transfer, use the ble_app_uart example, but the speed is too low , sniffer show that the notify pack moredata is true , but the follow pack is not...
Hello,
as far as I know the TLS implementation in the NRF9169 MFW does currently not support Connection Identifiers for DTLS 1.2 .
Are there any plans or a timeline when...
I have a nRF9160 DK (sn 000960004886) that has been working fine, I've tested out to build and load some of the application samples (blinky, hello_world) and they all worked...
Hey!
I am programming on the nrf52dk connected with debug out with an HW using the nrf52805 BLE soc.
My Colleague is already programming with the Segger Embedded Studio...
[Bootloader is based on NRF SDK v11]
I am experimenting with the NRF SDK v11 bootloader source code and want to trigger the UART/serial DFU as the bootloader starts. Right...
hi,
I am running openthread coap_client sample from NRFconnect SDK v1.6.1 and I have enabled joiner in my code.
But still, when I flash the code on nrf52840dk_board, it...
Hi!
I am working on a project with NRF51422QFAB.
First I tried a simple program, which runs well.
After that I would like to try out my own board antenna with the...
Hello everyone!
This is actually more a suggestion to improve flexibility for NCS integration (i.e. nrf-sdk) into Zephyr workspaces. In many CMake- and Kconfig files there...
