Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
Hi,
I am using a nRF52840 and SDK 15.2, and Soft Device S140 (BLE), where the device is battery powered.
In certain modes, the device sleeps to System Off mode, and...
I am currently porting the nrf_cc3xx_platform library to use it with RIOT OS . Following what has been done for Zephyr and FreeRTOS, I implemented:
Abort API
nrf_cc3xx_platform_abort_init...
Hello, I am working with the asset tracker v2 application and I want to connect it with Aws Cloud. I follow the steps corresponding to the tutorial and I am not successful...
I am trying to use the pc-ble-driver and as a first step want to use the heart_rate_collector example. I downloaded the source as follows:
I then followed the instructions...
Hi everyone,
I have an nRF52832 embedded as part of a dual chip (connected via SPI) and I'm looking to reduce the sleep current as much as possible. I'm currently measuring...
Hi, On both nrf52840 DK and Dongle, the sticker shows 4 info: - PCA board ID - version - year.month - Serial Number/MAC Address Could you please clarify what the last value...
Dear Nordic Community I am trying to get the nrfx adc driver to work with zephyr ( link ). With the help of this post , I ended up with the following code:
prj.conf -> ...
Dear Member,
I want to add ADC the main code,
but I got :
.\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol nrf_drv_ppi_init (referred from adc.o).
I'm using...
Hi, I am not sure whether there is I2C pins on nRF52840 Dongle board as based on the Adafruit Feather nRF52840 Express the pin is P0.11 and P0.12 as shown below: SCL 0.11...
Hello I am learning how to connect timers with gpio via PPI, i working on nrf52832dk.
So far I have connected the RTC 0 alarm channel to the LED no.3 (pin no.19) and its...
Hi, I am Shuang. I am now working on the Bluetooth direction finding function, but I have some problems, and I hope I can get your help.
I have experimented with Bluetooth...
I know Thingy:52-FW project has been marked as deprecated. https://github.com/NordicSemiconductor/Nordic-Thingy52-FW
However, I'm trying to get the development environment...
Hi，
I am using the ZBOSS SDK to develop the zigbee function, and I see that there are
TRACE_MSG(TRACE_ZCL1, ">> zb_zcl_finish_and_send_packet_common param %hd delay %d...
Hi,
based on my previous post/question here and after I managed to cconnect 5 specific address devices/peripherals from my central (DK) based on filtering (solution in the...
