Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hello ,
What is the purpose of the second line of the code in errata 89 ?
I mean this line ;
*(volatile uint32_t *)0x40003FFC;
did you use this one like nop ?
...
I need to install a BTLE application on an nRF52840 dongle that is enclosed in a case and therefore I do not have access to the reset button.
I have looked at some of the...
Hi, I'm using nRF52805.
My BLE code could connect & communicate data perfectly for the first time. After the disconnection, I can still see the signal. However, when I try...
Hello, new-to-this platform dev here!
I am implementing BLE bonding on my nRF52840 DK, which uses the S140 Softdevice. The DK is a peripheral and I'm using version 17.1...
Hi,
I need some help to choose an RF module for a new project.
I need:
* To connect to nRF24L with custom radio communications
* to connect to legacy standard bluetooth...
I use the nRF5_SDK_15.2.0_9412b96 , the sample is use a QSPI FLASH(MX25R64), and we want to change this QSPI FLASH. we will use GD25Q64E, which code should be modify?
I have developed a project with 9160, which requires real-time display of NB network signal on the screen. In order to save power consumption, I have set the Mode to PSM Mode...
Hello,
For us our IO rail is 1.8V. In this case do you see a big difference in power consumption whether REG1 is in LDO mode or DCDC mode? From 1.8V to 1.3V if in LDO mode...
Hi.
I use latest version of sdk and mesh. I run co-exist example as client and server in switch-light example as server. in client side i have add group address as you have...
Hello:
I had the Thingy91 (nrf9160) configured and working, but after a while, I tried to test it again, and I started seeing these errors:
- When using the LTE Link Monitor...
Hello,
I am working with DFU in the nRF Connect App and its working fine. Now I want to switch to the Android-DFU-Library and I always get "DFU CHARACTERISTICS NOT FOUND...
Hello,
I am currently using mqttsn publisher exams with keep allive time of 30 seconds, so according to MQTT standard if period of inactivity will be 45 second and the client...
Hello,
I would like to sign a firmware image with a custom private key. This is intended for OTA firmware update. The key type is ecdsa-p256 and the file containing the...
Hi，
sdk：ncs v1.6.1
board:9160dk_nrf9160
I use RTT to output log data, but I found that it can only output about 1k characters each time. Where can I modify it?
this...
Hi Team,
These are the SDA and SCL lines of nRF52832 connected to a sensor. the clock frequency defined in the code is 400 KHz, but its coming as 200 KHz on oscilloscope...
