Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi,
after migrating functional project to latest ncs version v1.5.0 I managed to build and flash it to nrf52840 board without problems. However if I enable MCUboot option...
Hi guys,
I want to add the function of multiple slaves to the nrf_desktop routine to support two hosts to connect to the keyboard .This routine is in the ncs1.4.1\v1.4.1...
Hi,
My application is to scan BLE advertising packet.
My application works when the scan_phys is set to BLE_GAP_PHY_1MBPS.
params.active = true; params.interval = NRF_BLE_SCAN_SCAN_INTERVAL;...
I'm specifically interested in the predefined SPIMn - SCK, MOSI, MISO, SO pins for this device, so that I can marry this information into my CPU Schematic Page. Whilst the...
Hello,
In our application, we have an external watchdog IC. We need to test the timing of that chip during our board power-on self-test.
We currently achieve this by setting...
Hello!
Recently we have noticed that some of our devices has been reporting strange fulgurations on their reported battery level. This is a graph over 24 hours:
When...
Hi I am the evaluation board of nRF52832 (TAIYO YUDEN Evaluation Board) EBSHSNZWZ) is used. I want to use P0.09 and P0.10 of nRF52832 as PIN of GPIO(TWI). It was set according...
Hi,
I'm developing a serialization system with nRF52832 and an application chip. My product is a power-sensitive.
The code of ble_connectivity in nRF5 SDK 17 calls nrf_drv_clock_init...
I've run into an issue with FOTA updates. The issue can be described by the following sequence of events:
A device is completely erased and programmed with a binary image...
Hi,
I am working on programming a bootloader on a NRF52840 DK using a different NRF52840 DK. Currently I have them connected via the debugger and have been successful in...
I am trying to port my build from Eclipse (based on the GCC tool chain) to a KEIL uVision build system.
I am using KEIL ARM Compiler version 6.15. Most of the files compile...
I see many similar questions to this, but I want to double check my understanding.
We have the nRF52840 connected to D-/D+ on a USB Type-C connector. We have a standalone...
Hi all!
I'm using an nRF52833, SDK 17.0.2, s140 softdevice 7.2.0. My design uses a Skyworks SKY66112 amplifier.
I have the pa_lna_assist function that I found here on...
I am running the example:
C:\Nordic\nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_bootloader\pca10040_uart_debug\arm5_no_packs
Everything seems to be working well except...
