Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am using the "ble_app_multilink_central" in version nRF5_SDK_17.0.2_d674dde for development.
It works and can connect to BLE devices.
However, there is one issue
...
I'm trying to use the BLE CLI example (ble_app_interactive) available on nRF5_SDK_17.0.2 on my nRF52840 chipset (on a BL654 kit) and as soon as the interface starts I receive...
Greetings,
I've got the power profiler app (v3.0.3, installed via the nRF connect desktop app v3.6.1) running under both Linux and Windows.
With windows, seems to work...
Hi, everyone,
I am pretty new to nRF52 development. Right now,I want to turn SAADC off at low power and turn it back on when wake up, but after nrfx_saadc_uninit(); When...
I am configuring the ANT+ scan on two separate channels with the following parameters:
ROMDATA_T ant_search_config_t aprfant_dynastream_search_config = { .channel_number...
Hello,
I am currently evaluating Nordic Thingy 52. I am planning to receive the sensor data on my custom BLE application (will be written in C using libbluetooth) running...
Hi
Attached is my pcb file. I select nrf52805_caaa, Can you help me check the pcb file? maybe the pcb is something wrong. I can download hex ,but can not debug it , when...
*** SOLVED PARTIALLY ***
Hello again,
I solved my problem partially, the part that reads accelerometer value and transmit BLE advertising data as beacon works fine.
...
Hi,
I want to use a MPU6050 sensor with my nrf52832 board.
I connected the SDA and SCL pins of my sensor board with the pins P0.26 and P0.27 of my nrf52832 board, respectively...
Hello. I'm working with multilink example and I've got some problem. I want to send data to specific peer device, but after restart central or one of the peer, they reconnects...
Hi. I have a problem with Segger Embedded Studio. I always get more than 100% of RAM usage when building project on SES, even if examples projects from SDK . Anyone know what...
Hello, I have the following question. I'm trying to program my firmware via DFU Bootloader and nRF Connect (smartphone). That works perfectly with the test board SparkFun...
Hi,
I am using the two units talking with each other for the BLE uart.
One is running with the example ble_app_uart_c_central. The other is running with the ble_app_uart_peripheral...
Hi, After updating my nrfConnect to 3.6.1, I had issues using my J-link being unrecognized in the programmer app. The J-link I'm using is part of a Silicon Labs Dev Kit, checking...
Hi, I was wondering if there are any problems with connecting VDD to an external power supply when using nrf52840 in the high voltage mode? I would like to connect VDDH to...
