I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
I'm trying to make an application which displays signal transferred via bluetooth.
To reduce computing time on the tablet, I want to apply oversampling in nRF52840.
The...
Thanks in advanced. I achieve 4 uint8_t dynamic sensor datas, I want 52832 transmit them through BLE continuously. Based on examples\ble_peripheral\ble_app_gatts_c, I can...
Dear,
How to evaluate a channel if is clear in property in NRF528 serials? e.g. there are ED and CCA in 802.15.4 standard, how to implement CSMA in NRF52810?
Hi
I'm using nRF52832, SDK 16.
When I enabling timer application the power consumption is increased by ~450uA, far away from the product specification
What may cause...
Hi there,
We're trying to write to the UICR CUSTOMER register to store some of the manufacturer info, such as BLE MAC address, for example.
When SD isn't running we have...
The following is loaded into flash on the nRF52840: Bootloader: 0xe0000 Application: 0x27000 SOFTDEVICE S140: 0x1000 MBR at 0x0000
Bootloader starts, waits 5 sec and runs...
Hello,
I want to use BLE direction finding. In the product brief ( https://www.nordicsemi.com/-/media/Software-and-other-downloads/Product-Briefs/nRF52833-DK-PB-10.pdf?la...
Hi,
I need some help to interpret the LTE timers values that my network operator applies.
During network registration I requested RPTAU : 10 min and AT : 0 min, by issuing...
I want to connect the nordic ZigBee with Digi's XBee module.
I have configured the Digi XBee pro s2c module as coordinator and nordic as a router but they are not communicating...
Continuing the discussion that was documented here:
https://devzone.nordicsemi.com/f/nordic-q-a/64691/how-to-use-the-latest-version-of-californium
1) I modified the resources...
Dear Nordic Support Team,
I haven't seen any forum posts directly applicable to the issue I'm seeing so I hope you can point me in the right direction.
The basic Thread...
I wanted to try to test some of the nrfx_saadc v2 features in a project I'm developing. I downloaded and ran a couple of the examples from GitHub and they run fine on a nRF52...
Hi,
we are facing the following error. We bond our device (peripheral S140, SDK 15.3) with the following settings with iOS devices:
#define SEC_PARAM_BOND 1 // Perform...
Hi,
I am unable to build code. My Mac has just been updated to Catalina, not sure if that's caused the issue.
I am trying to build the standard "blinky" code but am getting...
