Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am using nRF SDK v16 with nRF52DK pca10040 board and s112 soft device.
I understand that peer manager can remember each peers' CCCD setting following the bluetooth BLE...
We are evaluating the nRF52832 and have the following questions:
What is the accuracy of the internal ADC voltage reference and the voltage regulators?
Are any of the...
I am using windows 10 and have been able to work with the FOTA sample for the nrf9160 for several months.
I needed to update the SDK from 1.0.0 to 1.1.0. I followed the...
I've been trying to get my 6 Thingy:91s up and running for months now, and the customer is getting really frustrated by the many delays.
I first went through a series of...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1.
Till now I am using ‘ble_app_blinky’ example code, modified to my custom profile and tested On/Off...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
Whether can I call fds_record_update...
During a DFU on SDK15.2 the BLE connection is terminated. The NRF_BL_DFU_INACTIVITY_TIMEOUT_MS is set to 120000.
After 2 minutes, the device still has not reset and started...
Hello,
In the Pin Assignments paragraph of document nRF5340_OPS_v0.5.1 the following pins have no description
B12, A25, B26, J31, T2, K2, H2, G1, F2, D2, A1, A31, AL1...
Dear experts,
My BLE peripheral device uses s112 soft device with nRF52832 and nRF SDK v16 and now the basic data collection and transmission features all work fine with...
We are using the nRF51 bootloader to support DFU over serial. We were able to use the example bootloader as a great reference. We are able to successfully update our app using...
Hello I am trying to develop an application with NRF52833 development board and s113 softdevice.
I want to create a write characteristic which requires 247 ATT-MTU size...
I am trying the ble_app_gls example of nRF SDK v16.0 on nRF52 DK device. The only modification is change s132 to s112.
After download the app to nRF52 device, I can successfully...
So what I want to ask is what is the scan latency during high accuracy and low accuracy?
Also if an insight regarding power consumption can be given would be great (we are...
