Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
Hi,
I'm working on a Keyboard&Touchpad project, very similar configuration with Smart Remote 2, so I'm considering to use nRF24LU1+ as receiver's MCU. The receiver will be...
uint32_t ble_advdata_set (const ble_advdata_t *p_advdata, const ble_advdata_t *p_srdata)
If I set the second parameter p_srdata, does it mean passing encoded advertising...
Hi developers,
Just wondering if anyone has worked with a good BLE Python library that he can recommend. I have BLE peripherals that send out notifications. What I'd like...
Hi guys,
I am new to Nordic and I am using the evaluation kit "pca10001".
I have managed to run the LED BUTTON example which was declared in application note "nAN-36...
Hello,
I'm trying to connect to nrf connect with the nrf9160 DK. I am using an Irish vodafone NB-IOT sim to establish the connection. This sim has an access control list...
Hi,
I have a question regarding a DFU update via BLE. I am using mesh sdk v3.20 and sdk v15.30 with custom hardware (nrf52840).
I have the BLE DFU working as expected...
Hi all,
I am using mesh sdk3.20 and sdk15.30.
I noticed that with the buttonless ble dfu, it is not possible to perform a DFU transfer after the device was provisioned...
I did the program using examples of glucose. But I do not want to enter passkey from central. Because there is no LCD or UART in my device. Which part of the glucose example...
I am developing firmware for my Peripheral Device (nRF52840) using S140 (v7) and SDK 15.3. In my application, I will advertise (with advert payload changes) and support Smartphone...
Hi,
How much is the expected time period from the time VDD goes above 1.75V to main()? I am using a custom bootloader and am seeing a ~4.5s (yes seconds!) delay in getting...
i'm trying to configure the nrf to rx and according to the state diagram i realized that: as the nrf is supplied and the voltage goes over 1,9V the nrf goes in the power down...
Hi, i'm using the nrf24l01 with a zynq board to use it as radiocontrol; i'm trying to configure the nrf as receiver so that i'm able to send data from another nrf connected...
Hi, i'm using the nrf24l01 with a zynq board to use it as radiocontrol; i'm trying to configure the nrf as receiver so that i'm able to send data from another nrf connected...
I am trying to use the LPCOMP API, but I am having trouble with the following function:
nrfx_err_t nrfx_lpcomp_init
(
nrfx_lpcomp_config_t const *
p_config ...
I'm attempting to setup GPIOTE for an output that is set and cleared by different events. The GPIOTE driver doesn't let me initialize an output twice. Is there a way to do...
I have 2 objectives BT beacon and concurrent ESB with Thread using time slotting A. I would like my thread devices to broadcast BT beacons. As this does not require any reception...
Hello. We have product based on NRF51822 chip. 24 bit 4 channel ADC connected through SPI to MCU. Data rate is 250 Hz (4 ms). We send two ADC samples evry notification packet...
I started setting up Zephyr SDK development on my W10 laptop, according to the nRF Connect for Desktop guide, but running into this error when executing pip requirements installation...
Hello,
I'm writing a BLE app that acts as a peripheral and a broadcaster. If a connection is established, I'd like to continue advertising but update the advertising parameters...
