Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello. I have a problem with enabling nrfx module. I get this error during prohect compilation: 'NRFX_TWI0_INST_IDX' undeclared here (not in a function); did you mean 'NRFX_TWI_INSTANCE...
Hi,
I'd like to set 3 nrf52840-DK in the following way :
One device acts as central
2 devices acts as peripheral
I'd like the central to be connected to both peripherals...
I have custom board with nrf 52832. I am using SDK 12.3.0. and soft devices s132 V3.0.0 to transmit advertising packets with advertising interval 1s. I have written simple...
I already have a few devices in the field, and I'm curious if it is possible to occasionally update the signing key (e.g. to upgrade key, or compromised key, etc). If not...
Hello, I want to establish a connection between NRF52832 IC and ESP32 Module.
I implemented BLE on ESP 32 and achieved communication between Nordic Mobile app and ESP32...
Hi,
I am trying to used the WINC1500 Wifi module with the nRF9160 DK but I am not getting any data back from the module.
I am using the module
https://www.microchip...
Dear Nordic Support,
I follow this SAADC example to calibrate the SAADC every SAADC_CALIBRATION_INTERVAL.
However, whenever the function nrfx_saadc_abort() is called...
I am running into a strange issue. I want the bootloader to start automatically when I power on the device and then start the application if there is no activity after 30...
Hi,
If I want compiler my project at specified locate, the only thing tat I need to do is following image? Is it right?
After I program this program into address 0x0001D000...
I am trying to make PN7150 work with nRF52840 using TWI Communication.
Problem : PN7150 gets detected with I2C scanner example when using Adafruit Bootloader and programmed...
When I run "pc-ble-driver-py/pc_ble_driver_py/examples/serial_port_enum.py" on armv5tejl GNU/Linux 4.2.6+ (32 bit) connected with NRF52 DK, it is throwing an exception
...
Hello,
I wanted to add additional info to my question https://devzone.nordicsemi.com/f/nordic-q-a/50846/secure-bootloader-timeout-not-working-on-s132-15-3-sdk-with-logging...
I am trying to save rssi data that I print to the command line to a .csv file.
In the ble_app_interactive example in the cli_m.c file, here is my code:
Without the following...
Hi
I have the Adafruit Feather nRF52 Bluefruit - nRF52832 board that I can program it using Arduino via Adafruit library in Arduino without any problems.
Now I have an...
How can I disable all code-optimizing in SEGGER ?
I build and modify some Nordics example-tutorials using nRF52832 and want start debugging.
Best regards Lennart Vedin...
