Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi
I am using nrf51822 , sdk version 11 and softdevice version 130
In project I am trying to disable SPI1 and TWI0 channel by using following command
NRF_TWI0->ENABLE...
Hi, I are using BT832 module based on NRF52832-QFAA IC in an application. Please provide the following details regarding ble transmission of NRF52832-QFAA-R7 IC
1) modulation...
Hello,
I´ve got a corrdinator, which establishes my network. Also I´ve got an End-Device that joins the network successfully.
Is there any chance for me to observe the...
Hi Nordic,
I am working on a project where I connect via nrf52 DK, to a peripheral. I am runinng on SDK15, with the experimental build ble_app_interactive, inside the ble_central_and_peripheral...
I'm using nRF52832 with SDK 15.0 and Softdevice S132. Within ble_dfu.c anytime a connection is established the on_connect function blindly sets m_dfu.conn_handle = p_ble_evt...
hello nordic ,
i want to download the mesh SDK 2.1.1 to use the light switch example to transform the model simple onoff from sending uint8_t to string ,
i have started...
Hello, I'm using softdevice 6.0 and SDK 15.
In my application, I would like stop the SAADC at the disconnection and then restart SAADC at the connection to power saving...
hi..........
i am using nrf42840 ...segger 15.2 version
i am facing the problem in sleep mode
i used the command to sleep
static void power_manage( void ) { ret_code_t...
Hi guys,
I am currently using nrf51822 with SDK 11. I use Peer Manage to deal with paring and bonding encryption in BLE connection.
Please correct me if I am wrong but...
Hi,
When I'm trying the throughput on nRF52840 with SDK v14.2, I set up a 52840PDK as a 'repeater'; in which case the 'repeater' will receive the output (20kBytes in total...
which app should I use when I want to do LL BQB test with harmony on nRF52840?
it can not connected with harmony when I use DTM project. It seems the interface of nRF52840...
Dear nordic,
I am currently working with nRf52840. For designing antenna is there any role for dielectric layer thickness and conductive copper layer thickness
Hi all, I'm testing quick connections and communications using multilink(nus). I am using multilink central example in nrf52832(Central : softdevice v2.0.0 & SDK v11, Peripheral...
